4.6 Won't Update From Saved Report

[Mkelcy]

I've been attempting to update to 4.6 Router from 4.5 using a report to restore my settings. I followed the procedure in the updating to 4.5 video, but I don't get the screen in the Wizard at 10:27 of the video, that gives me the option to update the wizard. 4.5 report that I'm trying to use attached.

[mrp192]

I noticed this also. Some things did update but not everything.

[martyscncgarage]

You may be better off hand copying your settings over to 4.6
Hopefully you had screen shots of all your Wizard settings. It took me about 15 minutes a machine.

[Mkelcy]

Marty: I would do that, but I don't know how to edit the Axis drive type - I can get into the "custom" screen" but don't know how to make changes. I'm using a step rate of 200,000 and 16,383 steps/revolution.

[Mkelcy]

While I'm at it, there doesn't seem to be a SlavedHomeInput in 4.6. What do I use instead?

[martyscncgarage]

SlavedHomeInput is under the HOME drop down on the Input screen:

You also have a BUNCH of Communications Errors. And Error Initializing MPU
F7 Utilities, F9 Logs, F1 Errors.

Did you address this?:
(4) 01-08-2021 17:16:25 946 PC resending # 116377
(4) 01-08-2021 17:16:25 944 MPU requested resend # 2651
(4) 01-08-2021 17:16:25 946 PC resending # 116416
(4) 01-08-2021 17:16:26 944 MPU requested resend # 2652
(4) 01-08-2021 17:16:26 946 PC resending # 116426
(4) 01-08-2021 17:16:26 946 PC resending # 116476
(4) 01-08-2021 17:16:27 944 MPU requested resend # 2653
(4) 01-08-2021 17:16:27 946 PC resending # 116535
(4) 01-08-2021 17:16:30 944 MPU requested resend # 2655
(4) 01-08-2021 17:16:30 946 PC resending # 116596
(4) 01-08-2021 17:16:30 946 PC resending # 116644
(4) 01-08-2021 17:16:31 944 MPU requested resend # 2657
(4) 01-08-2021 17:16:31 946 PC resending # 116706
(4) 01-08-2021 17:16:31 944 MPU requested resend # 2658
(4) 01-08-2021 17:16:31 946 PC resending # 116762
(4) 01-08-2021 17:16:33 944 MPU requested resend # 2659
(4) 01-08-2021 17:16:33 946 PC resending # 116797
(4) 01-08-2021 17:16:39 944 MPU requested resend # 2660
(4) 01-08-2021 17:16:39 946 PC resending # 116841
(4) 01-08-2021 17:16:41 944 MPU requested resend # 2661
(4) 01-08-2021 17:16:41 946 PC resending # 116902
(4) 01-08-2021 17:16:43 944 MPU requested resend # 2662
(4) 01-08-2021 17:16:43 946 PC resending # 116953
(4) 01-08-2021 17:16:43 944 MPU requested resend # 2663
(4) 01-08-2021 17:16:43 946 PC resending # 116987
(4) 01-08-2021 17:16:46 944 MPU requested resend # 2664
(4) 01-08-2021 17:16:46 946 PC resending # 117047
(4) 01-08-2021 17:16:47 944 MPU requested resend # 2665
(4) 01-08-2021 17:16:47 946 PC resending # 117091
(4) 01-08-2021 17:16:48 944 MPU requested resend # 2666
(4) 01-08-2021 17:16:48 946 PC resending # 117143
(4) 01-08-2021 17:16:49 944 MPU requested resend # 2667
(4) 01-08-2021 17:16:49 946 PC resending # 117172
(4) 01-08-2021 17:16:49 946 PC resending # 117188
(4) 01-08-2021 17:16:56 944 MPU requested resend # 2668
(4) 01-08-2021 17:16:56 946 PC resending # 117190
(1) 01-08-2021 17:28:38 204 Exiting CNC...Normal Exit (66)
(1) 01-14-2021 14:03:59 199 CNC Started
(1) 01-14-2021 14:04:05 CNC12 Acorn Mill v4.50
(4) 01-14-2021 14:04:07 9033 Reset Initiated, Press Reset to Clear
(1) 01-14-2021 14:04:23 Created Weekly Report
(4) 01-14-2021 14:04:51 4032 Reset Cleared
(1) 01-14-2021 14:04:56 FAST_JOG_SELECTED
(4) 01-14-2021 14:05:11 5038 SPECIFIED SPIN SPEED < MIN SPIN SPEED
(1) 01-14-2021 19:08:51 204 Exiting CNC...Normal Exit (66)
(1) 01-16-2021 11:52:45 199 CNC Started
(1) 01-16-2021 11:52:52 CNC12 Acorn Mill v4.50
(4) 01-16-2021 11:52:52 9033 Reset Initiated, Press Reset to Clear
(4) 01-16-2021 11:52:56 4032 Reset Cleared
(4) 01-16-2021 11:52:59 5038 SPECIFIED SPIN SPEED < MIN SPIN SPEED
(1) 01-16-2021 11:53:04 FAST_JOG_SELECTED
(1) 01-16-2021 11:53:14 SLOW_JOG_SELECTED
(1) 01-16-2021 11:56:24 FAST_JOG_SELECTED
(1) 01-16-2021 14:48:51 204 Exiting CNC...Normal Exit (66)
(1) 01-18-2021 17:38:16 199 CNC Started
(1) 01-22-2021 8:24:32 102 Error initializing CPU...cannot continue.
(1) 01-22-2021 8:24:34 201 Exiting CNC due to a known error (63)
(1) 01-22-2021 8:43:10 199 CNC Started
(1) 01-22-2021 8:43:17 CNC12 Acorn Mill v4.50
(4) 01-22-2021 8:43:18 9033 Reset Initiated, Press Reset to Clear
(1) 01-22-2021 8:43:34 Created Weekly Report
(4) 01-22-2021 8:47:33 4032 Reset Cleared
(4) 01-22-2021 8:47:37 5038 SPECIFIED SPIN SPEED < MIN SPIN SPEED
(4) 01-23-2021 11:30:06 9031 DRIVE FAULT!
(1) 01-23-2021 17:44:00 204 Exiting CNC...Normal Exit (66)
(1) 01-27-2021 15:39:46 199 CNC Started
(1) 01-27-2021 15:39:52 CNC12 Acorn Mill v4.50
(4) 01-27-2021 15:39:52 9033 Reset Initiated, Press Reset to Clear
(4) 01-27-2021 15:39:56 4032 Reset Cleared
(4) 01-27-2021 15:40:06 5038 SPECIFIED SPIN SPEED < MIN SPIN SPEED
(1) 01-27-2021 15:53:30 FAST_JOG_SELECTED
(1) 01-27-2021 16:44:19 204 Exiting CNC...Normal Exit (66)
(1) 01-27-2021 19:52:22 199 CNC Started
(1) 01-29-2021 13:07:17 102 Error initializing CPU...cannot continue.
(1) 01-29-2021 13:07:19 201 Exiting CNC due to a known error (63)
(1) 01-30-2021 12:21:13 199 CNC Started
(1) 01-30-2021 12:21:20 CNC12 Acorn Mill v4.50
(4) 01-30-2021 12:21:21 9033 Reset Initiated, Press Reset to Clear
(1) 01-30-2021 12:21:40 Created Weekly Report
(4) 01-30-2021 12:21:40 4032 Reset Cleared
(4) 01-30-2021 12:21:40 9033 Reset Initiated, Press Reset to Clear
(4) 01-30-2021 12:21:40 4032 Reset Cleared
(4) 01-30-2021 12:21:40 9033 Reset Initiated, Press Reset to Clear
(4) 01-30-2021 12:21:41 4032 Reset Cleared
(1) 01-30-2021 12:22:23 Creating report...
(1) 01-30-2021 12:22:25 Saved report to C:\Users\MyPc\Documents\Centroid Documents\report_7804732BCC31-0227191699_2021-01-30_12-22-22.zip
(1) 01-30-2021 12:33:44 204 Exiting CNC...Normal Exit (66)
(1) 01-30-2021 12:34:32 199 CNC Started
(4) 01-30-2021 12:34:36 9039 Software Exited, Cycle E-Stop/Reset to Continue
(1) 01-30-2021 12:34:39 CNC12 Acorn Mill v4.50
(4) 01-30-2021 12:34:39 9033 Reset Initiated, Press Reset to Clear
(1) 01-30-2021 12:35:00 204 Exiting CNC...Normal Exit (66)
(1) 01-30-2021 14:55:40 199 CNC Started
(1) 01-30-2021 14:56:10 CNC12 Acorn Mill v4.50
(4) 01-30-2021 14:56:11 9033 Reset Initiated, Press Reset to Clear
(1) 01-30-2021 14:56:36 Creating report...

[martyscncgarage]

DId you try any of the Beta's with Router in them?
If not, since you are coming from Mill, I don't think your license is going to work with Router and you will have to upgrade to a Router License.

[Mkelcy]

Marty you got me thinking about mill versus router license. I tried installing 4.6 mill just now, and it worked perfectly; I had been trying to install 4.6 router (I have a router). The issue is pretty clearly that I didn't know I had to have a router license. Oops.

[cnckeith]

see the Acorn page for explanation, Router CNC12 requires a Router License. there is a reduce cost Router license for a limited time if you have a pro mill license file. (CNC12 Mill works with Mill License file, CNC12 Lathe works with Lathe License file, CNC12 Router works with Router License file)

https://www.centroidcnc.com/centroid_di ... oller.html

"All the CNC features of Mill Pro but with a Router specific Virtual Operator Control Panel and the corresponding Router specific macros.

If you previously purchased Mill Pro you can for a limited time upgrade to Router Pro (#15077) for $79


If you previously purchased Mill Digitizing Bundle you can for a limited time upgrade to Router Digitizing Bundle (#15078) for $79"

[cnckeith]

i downloaded your report.zip and used 'restore report' and started that Wizard and did get the update Wizard message, i clicked update Wizard and then "write settings to cnc control" and everything updated just fine.