Search found 3098 matches
- Wed Nov 20, 2019 4:52 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: ALLIN1DC Auto Spindle
- Replies: 1
- Views: 1127
Re: ALLIN1DC Auto Spindle
You'll need to provide some additional information before anyone can help. Please refer to this post viewtopic.php?f=64&t=383 on how to create a current report on your machine setup and post some photos of the control setup.
- Tue Nov 19, 2019 1:58 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Pete Rondeau is video blogging his Acorn build on his Dyna Myte 2800 bed mill.
- Replies: 37
- Views: 19093
Re: Pete Rondeau is video blogging his Acorn build on his Dyna Myte 2800 bed mill.
One minor point from the latest video: 25.4 is an EXACT conversion between millimeters and inches. It is not an approximation.
- Tue Nov 19, 2019 1:25 pm
- Forum: Centroid Acorn CNC Controller
- Topic: intercon arc
- Replies: 4
- Views: 1594
Re: intercon arc
End point and radius arc moves take the starting point from the machine's current position. If you want it to start at Z0, then you need to make a move PRIOR to the arc move to position the tool at Z0 and then call your arc move.
- Fri Nov 15, 2019 9:55 am
- Forum: Centroid Acorn CNC Controller
- Topic: Help, weird error
- Replies: 7
- Views: 2836
Re: Help, weird error
Can you post a report taken right after the error occurs? The report you posted has the program listed as "ncfiles\NO_JOB_LOADED.cnc" so I don't know whether to trust the offset information in the file either. I suspect you don't have enough Z travel to go that low.
- Thu Nov 14, 2019 6:00 pm
- Forum: Centroid Acorn CNC Controller
- Topic: 8 position Toolchanger lathe
- Replies: 6
- Views: 1218
Re: 8 position Toolchanger lathe
The Acorn does not have any provisions for serial communication to devices. You can use bit signalling by turning Acorn outputs on/off and connecting those to GPIO pins on the Arduino and monitoring for state changes. Keith's response was because there is a good chance that an existing Acorn PLC pro...
- Tue Nov 12, 2019 11:22 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Yaskawa GA800 / GA700 inverter and Oak board
- Replies: 22
- Views: 7547
Re: Yaskawa GA800 / GA700 inverter and Oak board
The Centroid control can control the orient of the spindle electrically if it is running as a C axis with a regular servo drive connected. It cannot orient the spindle electrically if run as a regular spindle motor controlled with the spindle output. However, you can mechanically orient the spindle ...
- Thu Nov 07, 2019 3:30 pm
- Forum: Centroid Acorn CNC Controller
- Topic: ATC Spindle Proximity Switches
- Replies: 21
- Views: 7154
Re: ATC Spindle Proximity Switches
What's your PLC code for SV_M94_M95_15?
- Tue Nov 05, 2019 2:19 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: M-15 Training in Minnesota (RESOLVED)
- Replies: 41
- Views: 10385
Re: M-15 Training in Minnesota (RESOLVED)
I would suggest against a flood coolant system on a knee mill. It will make a mess. I suggest mist or MQL, (Minimum Quantity Lubrication) system. I second Marty's sentiments here and suggest you look at Fog Buster spray systems. I have them on two mill and two lathes and couldn't be happier with th...
- Wed Oct 30, 2019 10:04 pm
- Forum: Centroid Acorn CNC Controller
- Topic: building the controllbox (electric interference)
- Replies: 13
- Views: 5133
Re: building the controllbox (electric interference)
Anything that acts like an inductor - contactor coils, transformers, fans; basically anything with a coil of wire in it.
- Tue Oct 29, 2019 10:01 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Oak Control, Yaskawa Servos, on Brand New Rigid Head Bed Mill with ATC
- Replies: 39
- Views: 15604
Re: Oak Control, Yaskawa Servos, on Brand New Rigid Head Bed Mill with ATC
AXIS connector housings are JST #PUDP-30V-S and the crimp terminals are JST #SPUD-001T-P0.5.