Search found 129 matches
- Sat Nov 19, 2022 8:56 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Velocity vs position mode
- Replies: 4
- Views: 801
Velocity vs position mode
Ok i have talked to a guy who does alot of retrofits on older machines. Reason i started with that is because this isnt something i made up or looked into. But more asking the pros on here that have way more experience than me about this. I can run my drives in either mode. Leaning toward velocity j...
- Wed Nov 09, 2022 3:05 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Oak with lathe turret position questions.
- Replies: 18
- Views: 12357
Re: Oak with lathe turret position questions.
An encoder for turret-position feedback, while it occupies an axis number, does not count as a controlled axis. Even if it were a servo-controlled axis (as some turrets are), since you never move it while cutting, it would not be an issue. The 5-axis software is only required to move five axes all ...
- Tue Nov 08, 2022 1:21 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Oak with lathe turret position questions.
- Replies: 18
- Views: 12357
Re: Oak with lathe turret position questions.
Probably about the same amount of work. Using the 24 separate reed switches is awkward, in that the input you are watching for to trigger deceleration will be different for every tool position. You either end up with a lot of duplicate code, or you need to use indirect indexing, which is a little o...
- Sun Nov 06, 2022 8:56 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Oak with lathe turret position questions.
- Replies: 18
- Views: 12357
Re: Oak with lathe turret position questions.
You could do it with an encoder: for example, a 300-line incremental encoder would give the control 1200 counts per revolution, or 100 counts per tool. You could then use PLC logic to read the encoder position and determine when it is close enough to decelerate, and when it is close enough to stop....
- Sun Nov 06, 2022 3:01 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Oak with lathe turret position questions.
- Replies: 18
- Views: 12357
Re: Oak with lathe turret position questions.
well i guess im just buying another 1616 and keep the factory way of working. lol.
- Sun Nov 06, 2022 12:18 am
- Forum: Centroid Acorn CNC Controller
- Topic: 8000 RPM Spindle Encoder
- Replies: 8
- Views: 1289
Re: 8000 RPM Spindle Encoder
I have an Rls re22ic041d010f3c00 That I am going to use on belt drive system 1 to 1 but im not putting tension on the actual encoder, encoder will be connected by a motor coupling so that it doesn't have any side forces on it. https://www.rls.si/eng/re22-rotary-magnetic-shaft-encoder Here is link to...
- Fri Nov 04, 2022 11:07 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Oak with lathe turret position questions.
- Replies: 18
- Views: 12357
Oak with lathe turret position questions.
Ok i have a few questions for a retrofit im doing on my older mazak lathe. I have some manual information ill post pics of. But first thing is they are using 24 reed switch inputs. They use 2 per tool position first one is for slow down hydraulic solenoid and other is high. Looks like its all done w...
- Sat Oct 29, 2022 11:03 pm
- Forum: Centroid Acorn CNC Controller
- Topic: ProbeApp V3: The Ultimate Probe Software for CNC12
- Replies: 68
- Views: 119207
Re: ProbeApp V3: The Ultimate Probe Software for CNC12
Thanks that is what im going to do is make a swing down one that is in the centerline of spindle.
- Fri Oct 28, 2022 10:21 pm
- Forum: Centroid Acorn CNC Controller
- Topic: ProbeApp V3: The Ultimate Probe Software for CNC12
- Replies: 68
- Views: 119207
Re: ProbeApp V3: The Ultimate Probe Software for CNC12
This would work with one input since you can dial in probe diameter and thickness.... Uwe yes one input is fine. but im wanting to know if he can add it. Since the probe on a lathe will need to approach from 4 diff positions based on what tool you have to setup. like left hand or right hand tool, o...
- Fri Oct 28, 2022 8:16 pm
- Forum: Centroid Acorn CNC Controller
- Topic: ProbeApp V3: The Ultimate Probe Software for CNC12
- Replies: 68
- Views: 119207
Re: ProbeApp V3: The Ultimate Probe Software for CNC12
Thanks, so i assume thats the approach angle when we setup tool in the offset table.