Thanks for reporting back, yes cutting off should go much better now.
Uwe
Search found 1979 matches
- Tue Sep 13, 2022 2:25 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Toolpost mount for Acorn lathe
- Replies: 16
- Views: 1919
- Thu Sep 08, 2022 11:31 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Emco PC Turn 55 lathe recommended encoder.
- Replies: 1
- Views: 372
Re: Emco PC Turn 55 lathe recommended encoder.
Hi Hugo,
yes, this Omron works with 4000 rpm.
Uwe
yes, this Omron works with 4000 rpm.
Uwe
- Thu Sep 08, 2022 9:18 am
- Forum: Centroid Acorn CNC Controller
- Topic: Compiling error and potential fix
- Replies: 1
- Views: 339
Re: Compiling error and potential fix
Thanks for the info.
On my work PC I have another solution to get NppExec to compile without the use of compile.cmd
Uwe
On my work PC I have another solution to get NppExec to compile without the use of compile.cmd
Uwe
- Thu Sep 08, 2022 7:14 am
- Forum: Centroid Acorn CNC Controller
- Topic: Can fixed feed rate overrides be set by PLC input?
- Replies: 3
- Views: 543
Re: Can fixed feed rate overrides be set by PLC input?
Could work this way: Define the 4 Inputs FeedBit1 IS INP10 FeedBit2 IS INP11 FeedBit3 IS INP12 FeedBit4 IS INP13 and build logic for 4 bit Gray code ; Test 4 bit GrayCode for Feedrate - UWE IF !FeedBit1 && !FeedBit2 && !FeedBit3 && !FeedBit4 THEN KBOverride_W = 0 IF FeedBit1 ...
- Tue Sep 06, 2022 11:50 pm
- Forum: Centroid Acorn CNC Controller
- Topic: invisibe panel control with new version 4.80
- Replies: 10
- Views: 1427
Re: invisibe panel control with new version 4.80
I think it is an issue with your WIN10 setup.
On several 4.80 installs I never have had this problem. PCs were always configured for CNC use.
Uwe
On several 4.80 installs I never have had this problem. PCs were always configured for CNC use.
Uwe
- Tue Sep 06, 2022 3:06 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Simultaneous 4 axis moves on a lathe
- Replies: 32
- Views: 4899
Re: Simultaneous 4 axis moves on a lathe
Here is how the new spindle runs:
Uwe
Uwe
- Tue Sep 06, 2022 2:52 pm
- Forum: Centroid Acorn CNC Controller
- Topic: invisibe panel control with new version 4.80
- Replies: 10
- Views: 1427
Re: invisibe panel control with new version 4.80
Did you made a fresh install with Acorn 4.80, that means the old \cnc folder renamed or deleted and do not use restore report?
Uwe
Uwe
- Tue Sep 06, 2022 5:22 am
- Forum: Centroid Acorn CNC Controller
- Topic: Can fixed feed rate overrides be set by PLC input?
- Replies: 3
- Views: 543
Re: Can fixed feed rate overrides be set by PLC input?
Sure this is no problem with simple PLC editing, but if 4 Inputs are used, I would use a 4bit 16 Detent Gray Encoder. This gives you 16 steps feed rate with 4 Inputs.
Uwe
Uwe
- Tue Sep 06, 2022 12:28 am
- Forum: Centroid Acorn CNC Controller
- Topic: why when i tighten the gibbs on my dovetail mill the backlash goes up?
- Replies: 6
- Views: 742
Re: why when i tighten the gibbs on my dovetail mill the backlash goes up?
You also should move the vice from time to time, to get even wear of the slides over the whole length.
Most cheap asian machines need also scraping to get even play over the whole travel.
Uwe
Most cheap asian machines need also scraping to get even play over the whole travel.
Uwe
- Tue Sep 06, 2022 12:24 am
- Forum: Centroid Acorn CNC Controller
- Topic: Toolpost mount for Acorn lathe
- Replies: 16
- Views: 1919
Re: Toolpost mount for Acorn lathe
With CNC I use only 90° indexing 99° of the time.
Multifix was made for manual lathes to cur 30° chamfers ect.
With CNC you can use it with live tooling for boring at an angle or if you need tu turn 45° left side with DCMT...
Uwe
Multifix was made for manual lathes to cur 30° chamfers ect.
With CNC you can use it with live tooling for boring at an angle or if you need tu turn 45° left side with DCMT...
Uwe