Search found 370 matches
- Sat Feb 24, 2024 11:08 am
- Forum: Centroid Acorn CNC Controller
- Topic: Intercon enhancement request
- Replies: 8
- Views: 380
Re: Intercon enhancement request
Checkout fog buster by Noga which can be used used in air blast only and/or use vac for evac. No offence but allowing any machining of chips will damage or break you bit perhaps sooner than later with disastrous consequences
- Thu Feb 22, 2024 1:45 pm
- Forum: Centroid Acorn CNC Controller
- Topic: MDI Spindle Voltage Incorrect
- Replies: 5
- Views: 254
Re: MDI Spindle Voltage Incorrect
Disconnect wires from both Vout and COM analog terminals on Acorn and measure voltage on those terminals when manually commanding 1750 rpm. Does this produce 5vdc
Did you clean up wiring as we suggested in your other thread?
And PLEASE, post a new and current Report.zip
Did you clean up wiring as we suggested in your other thread?
And PLEASE, post a new and current Report.zip
- Tue Feb 20, 2024 8:56 am
- Forum: Centroid Acorn CNC Controller
- Topic: Lathe CAM post processor
- Replies: 2
- Views: 140
Re: Lathe CAM post processor
Since both Catia and Solidworks are under the Dassault umbrella, perhaps the following post may help
https://centroidcncforum.com/viewtopic.php?f=60&t=4101
https://centroidcncforum.com/viewtopic.php?f=60&t=4101
- Tue Feb 20, 2024 8:33 am
- Forum: Centroid Acorn CNC Controller
- Topic: Safe Spindle Temperature?
- Replies: 23
- Views: 1041
Re: Safe Spindle Temperature?
How about researching if Ceramic Bearings could be an option assuming they are available in your size. My air cooled Router spindle uses this up to 24K rpm but does need 10 minute warm up before use. However, I don't know the suitability for a Mill
- Tue Feb 20, 2024 8:23 am
- Forum: Centroid Acorn CNC Controller
- Topic: Z Axis Slips
- Replies: 6
- Views: 295
Re: Z Axis Slips
Please post a current Report.zip from your machine, ideally with hi-def photos of your control cabinet, which will help everyone understand your configuration
- Tue Feb 20, 2024 8:15 am
- Forum: Centroid Acorn CNC Controller
- Topic: 5v and db25
- Replies: 6
- Views: 224
Re: 5v and db25
The DB25 is supplied with 5vdc from the board itself i.e. not a separate supply. Centroid's Installation manual shows a photo on page 54 with connections as follows: - Red wire from DB25 Pin 2 to drive Pul+ - Black wire from DB25 Pin 3 to drive Pul - - Blue wire from DB25 Pin 18 to drive Dir+ - Yell...
- Sat Feb 10, 2024 1:29 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Unable to Set Spindle Speed via G-Code <resolved>
- Replies: 12
- Views: 529
Re: Unable to Set Spindle Speed via G-Code
Frankly, I'm surprised anything worked but at least you are now making progress. Why? Imagine trying to make sense of a phone call when you can only hear 1 word out of 3 in every other sentence and I'm not talking of selective hearing :mrgreen: I think you could also usefully tidy up / replace the w...
- Sat Feb 10, 2024 1:14 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Running Arbetrary NC Code
- Replies: 1
- Views: 129
Re: Running Arbetrary NC Code
Refer to section 3.3 of your Manual - MDI
- Sat Feb 10, 2024 12:36 pm
- Forum: Centroid Acorn CNC Controller
- Topic: CNC12 "Sticking" during Macros
- Replies: 24
- Views: 1155
Re: CNC12 "Sticking" during Macros
As a start, create a new Report.zip and post here
- Sat Feb 10, 2024 10:32 am
- Forum: Centroid Acorn CNC Controller
- Topic: Unable to Set Spindle Speed via G-Code <resolved>
- Replies: 12
- Views: 529
Re: Unable to Set Spindle Speed via G-Code
Your error log is absolutely full of MPU and PC resends. This MUST be addressed before trying to work out other issues as the system will not work properly until this is sorted.
Review Keith's post here https://centroidcncforum.com/viewtopic. ... 777#p82777
Review Keith's post here https://centroidcncforum.com/viewtopic. ... 777#p82777