Search found 56 matches
- Thu Mar 11, 2021 1:06 am
- Forum: Centroid Acorn CNC Controller
- Topic: Newbie converting a PM-728VT
- Replies: 83
- Views: 28702
Re: Newbie converting a PM-728VT
Marty do you know someone in the Phoenix metro who has a lathe and is willing to machine a short threaded 1/4" or 6mm hole in the top of my drawbar? I got the OMron encoder and jerry - rigged it on top without Franco's belt system, but I need to drill and tap a hole in the drawbar. I am of cou...
- Thu Mar 11, 2021 1:03 am
- Forum: Centroid Acorn CNC Controller
- Topic: Newbie converting a PM-728VT
- Replies: 83
- Views: 28702
Re: Newbie converting a PM-728VT
Based on the latest recommendations from Centroid, i have redone the wiring of the motors today -- I had originally cut off the molex and wired directly into the Acorn terminals. Today I have crimped molex spades back onto the wires and plugged in a CNC4PC ACCP board and followed Marty's wiring reco...
- Sat Feb 27, 2021 2:22 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Newbie converting a PM-728VT
- Replies: 83
- Views: 28702
Re: Newbie converting a PM-728VT
Real time feedback requires an encoder to be mounted at 1:1 to the spindle with timing pulleys and belt. Reach out to Franco and see if he'll print and sell you a bracket. He is a member on this forum The PM has a tachometer, and you can link up the 0-10V adapter board for the Acorn connection in s...
- Thu Feb 25, 2021 8:49 am
- Forum: Centroid Acorn CNC Controller
- Topic: Newbie converting a PM-728VT
- Replies: 83
- Views: 28702
Re: Newbie converting a PM-728VT
BE VERY CAREFUL Connecting that drive to Acorn Analog inputs. There needs to be signal isolation between them. Do you have a manual for that BLDC Drive? Post it here. Thank you Marty for these replies, they were very helpful, as always. I stopped the project and watched Franco’s videos. I do not ha...
- Wed Feb 24, 2021 10:09 am
- Forum: Centroid Acorn CNC Controller
- Topic: Newbie converting a PM-728VT
- Replies: 83
- Views: 28702
Re: Newbie converting a PM-728VT
I am not sure how to adjust the frequency on the PM 728. Here are some photos of the circuit (nothing obvious to adjust), front panel (the potentiometer is how you adjust the rpm), and motor. Sorry about the bad photos, could not reach better. So do I adjust the VFD, how else would I increase the ra...
- Wed Feb 24, 2021 1:13 am
- Forum: Centroid Acorn CNC Controller
- Topic: Newbie converting a PM-728VT
- Replies: 83
- Views: 28702
Re: Newbie converting a PM-728VT
I have run the spindlebenchtest but my mill has a max speed of 4250. How can i configure the voltage output to run the apindle over 3000 rpm?
- Sun Feb 14, 2021 9:51 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Newbie converting a PM-728VT
- Replies: 83
- Views: 28702
Re: Newbie converting a PM-728VT
Thank you gentlemen, I have ordered 3 NPN NC sensors from AutomationDirect. Hopefully they will play with the Acorn.
- Sun Feb 14, 2021 12:17 am
- Forum: Centroid Acorn CNC Controller
- Topic: Newbie converting a PM-728VT
- Replies: 83
- Views: 28702
Please help me choose proximity sensors.
I have finally received the mill (2-1/2 months after ordering it) and have taken it apart to do the conversion. Please help me choose induction proximity sensors. I do have no name sensors off eBay that work with the Acorn bench test, but I want to install quality sensors as a "do it once, do i...
- Mon Feb 01, 2021 9:20 am
- Forum: Centroid Acorn CNC Controller
- Topic: Newbie converting a PM-728VT
- Replies: 83
- Views: 28702
Re: Newbie converting a PM-728VT
Desert Rider, Thanks so much for sharing your recipe! Did you use the Centroid Clearpath schematci? Essentially yes. I wonder how can I wire in 6 inputs for the limits (X+, X-, Y+, etc). I'd much rather do it separately than to wire sensors in series. Does the Acorn allow that? I don't see how it c...
- Thu Jan 14, 2021 12:16 am
- Forum: Centroid Acorn CNC Controller
- Topic: Newbie converting a PM-728VT
- Replies: 83
- Views: 28702
Re: Newbie converting a PM-728VT
Great idea Marty, I will share here what I did thus far. I assume the Acorn board and its computer connection have successfully been bench tested. Before wiring Clearpath motors to the Acorn, one should set them up using Teknic's MSP setup software . You should download the Teknic user manual and re...