Search found 368 matches
- Sat Feb 03, 2024 10:47 am
- Forum: Centroid Acorn CNC Controller
- Topic: Tool setter positioning
- Replies: 4
- Views: 361
Re: Tool setter positioning
You can use G28 / G30 / G30 P2 / G30 P3 and set to be any position you like. Navigate as follows from main menu F1 Setup / F1 Part / F9 WCS Table / F1 Return. You now choose 1 of the 4 Return points (to match Clint's macro) and enter the appropriate co-ords remembering they are Machine Co-ords NOT W...
- Fri Feb 02, 2024 11:36 am
- Forum: Centroid Acorn CNC Controller
- Topic: Confused over home switches and limit switches
- Replies: 6
- Views: 423
Re: Confused over home switches and limit switches
I have A axis setup on my mill without a home switch and therefore it's homed in whatever position it happens to be. This is not a problem since it has a 3/4 jaw chuck / faceplate. However, in the event of an unexpected stop (power failure, programming SNAFU etc) midway through a job, you may need t...
- Fri Feb 02, 2024 11:18 am
- Forum: Centroid Acorn CNC Controller
- Topic: Experiences with GE vfd's
- Replies: 6
- Views: 431
Re: Experiences with GE vfd's
Full manual on this link https://www.inverter.co.uk/applications/manuals&datasheets/ge-vat2000-manual.pdf manualslib online manuals are about as useful as a chocolate welding nozzle :mrgreen: Post photos using the attachments tab after pressing Full Editor & Preview button on the Quick Reply...
- Mon Jan 29, 2024 10:27 am
- Forum: Centroid Acorn CNC Controller
- Topic: WMPG6 Controller issues < usb ports , don't use power save or sleep >
- Replies: 21
- Views: 1670
Re: WMPG6 Controller issues < usb ports , don't use power save or sleep >
No I didn't hand enter the field. I installed and then used the backup form the previous install from the Pentium computer since it was running the same machine, all I did was update the computer. Before I got the machine his WMPG-4 was working fine and had no issues. He made sure everything was up...
- Sat Jan 27, 2024 4:13 pm
- Forum: Centroid Acorn CNC Controller
- Topic: WMPG6 Controller issues < usb ports , don't use power save or sleep >
- Replies: 21
- Views: 1670
Re: WMPG6 Controller issues < usb ports , don't use power save or sleep >
Nigelo, The minimum your seeing is the old PC that ran the CNC mill it was a late 90s Pentium. No, quite the opposite. I see a Single Thread benchmark 1515 for the last Report in your zip timed at 17:10 on Jan 5 2024 where the CPU is an Intel Celeron N5105 @ 2.00GHz. See link https://www.cpubenchma...
- Fri Jan 26, 2024 9:12 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Machine movement calibration
- Replies: 5
- Views: 502
Re: Machine movement calibration
No, you do not "bring it back" at all and should not be using the wmpg to conduct these tests. Use mdi for the pre travel to your start point and set WCS X to zero. Read off your dti or set to zero and then use mdi again to move to X2 in the SAME as direction as pre travel at say F8 I.e G1...
- Fri Jan 26, 2024 6:19 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Machine movement calibration
- Replies: 5
- Views: 502
Re: Machine movement calibration
For a commanded move of 2" inches but actual travel of 1.997" with motor revs/inch currently set to 9.9991 try setting Motor revs/inch to 10.01412118 Save and then re-home before retesting This assumes your actual measurement is correct and you have indeed excluded backlash by pre-travelli...
- Thu Jan 25, 2024 5:03 pm
- Forum: Centroid Acorn CNC Controller
- Topic: MDI Spindle input not working (Error code: 5038) <resolved>
- Replies: 4
- Views: 378
Re: MDI Spindle input not working (Error code: 5038)
Go back into the Wizard and check your spindle speeds. You cannot run at less than the minimum entered here. Put simply, the system will always default to this minimum where you enter a lower speed
- Wed Jan 24, 2024 12:36 pm
- Forum: Centroid Acorn CNC Controller
- Topic: today i drafted a discussion paper on tool height offset methods
- Replies: 23
- Views: 1380
Re: today i drafted a discussion paper on tool height offset methods
My understanding: Uwe is saying his Axis "flag" passes across the face of the sensor rather than approaching head-on.
- Tue Jan 23, 2024 9:35 am
- Forum: Centroid Acorn CNC Controller
- Topic: Im having trouble accessing the interface
- Replies: 3
- Views: 272
Re: Im having trouble accessing the interface
Did you have an Acorn (or other Centroid board) connected to your PC when you installed the software?
If not and you just want to familiarise yourself, install the Offline version.
Need more info to help
If not and you just want to familiarise yourself, install the Offline version.
Need more info to help