Search found 529 matches
- Sun May 16, 2021 10:55 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Retrofit 2.0 TREE J325
- Replies: 132
- Views: 34884
Re: Retrofit 2.0 TREE J325
Since the motors are not a drop in replacement for the Baldor motors I am working on a mounting plate. I also need to determine if the pulley will align with the one on the ballscrews. Attached is a concept.
- Sun May 16, 2021 5:41 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Retrofit 2.0 TREE J325
- Replies: 132
- Views: 34884
Re: Retrofit 2.0 TREE J325
Some video to show progress
- Sun May 16, 2021 5:12 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Retrofit 2.0 TREE J325
- Replies: 132
- Views: 34884
Re: Retrofit 2.0 TREE J325
OK I missed the 24VAC note early on and got appropriate items for 24VDC. Is the AC stuff quieter or is there another reason for the preference? I believe what I have is now wired correctly and only has one software (?) Issue. I wrote a program to spin the motors and wanted to test the E-Stop. It sto...
- Sun May 16, 2021 1:03 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Retrofit 2.0 TREE J325
- Replies: 132
- Views: 34884
Re: Retrofit 2.0 TREE J325
AC I'm assuming that should be DC
The circuit for DYN4 below shows 24V- Sat May 15, 2021 2:03 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Retrofit 2.0 TREE J325
- Replies: 132
- Views: 34884
- Sat May 15, 2021 12:57 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Retrofit 2.0 TREE J325
- Replies: 132
- Views: 34884
Re: Retrofit 2.0 TREE J325
I bought a 24VDC power supply to drive contactors etc. Meanwell EDR -120-24 it can supply 5 amps but when I hook up three contactors it won't pull them closed - two will work. Contactor is a Fuji SC-E03-24. Is it possible that the 24 coils are pulling more than 5amps, can't seem to find that data. E...
- Fri May 14, 2021 4:34 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Retrofit 2.0 TREE J325
- Replies: 132
- Views: 34884
Re: Retrofit 2.0 TREE J325
DMM Parts arrived yesterday, one of the Styrofoam clamshell that protects the motor had a big hole punched in it from a pretty serious drop on the encoder end of the motor. I contacted DMM and will proceed with testing but I don't need any extra challenges... The first drive/motor has been wired up ...
- Wed May 12, 2021 9:45 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Retrofit 2.0 TREE J325
- Replies: 132
- Views: 34884
Re: Retrofit 2.0 TREE J325
I am reviewing the VFR manual in preparation for figuring out how to use the relays, that are now on order. There are options for 5 modes, and it sounds like wire proof PLC mode would be the one I'd use (a reasonable guess but if not,- the others are CD type interface, Mentor type interface, wire pr...
- Wed May 12, 2021 2:52 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Retrofit 2.0 TREE J325
- Replies: 132
- Views: 34884
Re: Retrofit 2.0 TREE J325
One area of control that I am working on is to find relays to use for E-Stop, spindle fwd/rev. I may not have enough I/O to run all the relays shown but I would appreciate some help with identification - manufacturer - vendor? Is 1 a time delay? relays.JPG Yes, relay 1 is a time delay (didn't you h...
- Wed May 12, 2021 2:48 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Retrofit 2.0 TREE J325
- Replies: 132
- Views: 34884
Re: Retrofit 2.0 TREE J325
Thanks Stephen Super helpful.