Hi Marty
That worked! I can now move motors thru cnc12 control panel.
Now it's time to get acquainted with navigating cnc12 .
I will convert my lathe next month.
Thank you for all the help! You are performing a great service for all us newbies!
Dave
Search found 119 matches
- Tue Jul 10, 2018 1:03 am
- Forum: Centroid Acorn CNC Controller
- Topic: Opening up cnc12 for first time (problems)
- Replies: 9
- Views: 2544
- Mon Jul 09, 2018 12:34 am
- Forum: Centroid Acorn CNC Controller
- Topic: Opening up cnc12 for first time (problems)
- Replies: 9
- Views: 2544
Re: Opening up cnc12 for first time (problems)
Hi marty
I changed wizard to simple home. opened up cnc12 and when I hit cycle start nothing happened, it still showed not home, i then hit button to bypass limit switches and then cycle start and cnc12 set home ,but i still could not move motors and got a driver fault alarm (see screen shot) attached
I changed wizard to simple home. opened up cnc12 and when I hit cycle start nothing happened, it still showed not home, i then hit button to bypass limit switches and then cycle start and cnc12 set home ,but i still could not move motors and got a driver fault alarm (see screen shot) attached
- Sun Jul 08, 2018 7:29 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Opening up cnc12 for first time (problems)
- Replies: 9
- Views: 2544
Re: Opening up cnc12 for first time (problems)
Hi Marty
yes using DB25 to connect drivers see attached photos
again, i appreciate your help immensely
Dave
yes using DB25 to connect drivers see attached photos
again, i appreciate your help immensely
Dave
- Sat Jul 07, 2018 11:03 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Opening up cnc12 for first time (problems)
- Replies: 9
- Views: 2544
Re: Opening up cnc12 for first time (problems)
Hi Guys I have attached a copy of the report, for my centroid acorn build. I watched a lot of videos and did some research, however, I'm very much a rookie when it comes to building a cnc controller box and linking computer software. Im working on taking and uploading pictures within the next few da...
- Fri Jul 06, 2018 9:19 pm
- Forum: Centroid Acorn CNC Controller
- Topic: com port issue
- Replies: 4
- Views: 1800
Re: com port issue
Thank you everyone! Im up and running, already benchtested my motors and saved parameters! My problem was my cnc controller box was wired wrong. Power was brought in and connected to the 24 volt power suppy directly and then power was routed to the main (large) power supply, this caused both the ser...
- Fri Jul 06, 2018 9:01 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Opening up cnc12 for first time (problems)
- Replies: 9
- Views: 2544
Opening up cnc12 for first time (problems)
Hi everyone I have DMM servo motors / drivers, i went thru bench testing motors and saved the perimeters, everything went good, motors worked great. I opened up cnc12 and because my motors are still on the bench i over rode limit switch on cnc12 control board and then set home position and then set ...
- Fri Jul 06, 2018 8:16 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Cant call up MDI page
- Replies: 1
- Views: 1091
Cant call up MDI page
Hi everyone I followed the set up procedures for motor tuning (bench test) and everything worked great,, i saved the perimeters And opened up cnc12 software. I have no limit switches hooked up motors are still sitting on the bench, so i over rode the limit switches on cnc12 screen. I set home positi...
- Thu Jun 28, 2018 5:21 pm
- Forum: Centroid Acorn CNC Controller
- Topic: com port issue
- Replies: 4
- Views: 1800
com port issue
hi all
I'm trying to bench test my DMM servo motors, i open the install file and it shows not connected, when i try to connect and let computer and software find the com port ,it says com 1.
how do i know what com port that is and how do i turn it on?
any help would be appreciated
I'm trying to bench test my DMM servo motors, i open the install file and it shows not connected, when i try to connect and let computer and software find the com port ,it says com 1.
how do i know what com port that is and how do i turn it on?
any help would be appreciated
- Sat Dec 23, 2017 2:25 am
- Forum: Success Stories
- Topic: Grizzly G0752 Acorn Retrofit
- Replies: 7
- Views: 5249
Re: Grizzly G0752 Acorn Retrofit
Hi Gary
Just wondering, where did you get the limit switches?
Do you have part numbers for the switches?
I would like to buy some of them
Nice neat conversion !
I m waiting on the same lathe to be delivered to me.
Just wondering, where did you get the limit switches?
Do you have part numbers for the switches?
I would like to buy some of them
Nice neat conversion !
I m waiting on the same lathe to be delivered to me.