If new SKF are on the way, use them. I am not sure if they have used high quality bearings in Taiwan.
Uwe
Search found 1973 matches
- Thu Feb 29, 2024 10:40 am
- Forum: Centroid Acorn CNC Controller
- Topic: Safe Spindle Temperature?
- Replies: 23
- Views: 1068
- Thu Feb 29, 2024 10:37 am
- Forum: Public Beta CNC Software Testing, Discussion and Feedback
- Topic: OPCON and USB-BOB
- Replies: 79
- Views: 4083
Re: OPCON and USB-BOB
What type of joystick will work to move the axes, and could it move diagonal ?
Uwe
Uwe
- Wed Feb 28, 2024 12:46 pm
- Forum: Public Beta CNC Software Testing, Discussion and Feedback
- Topic: OPCON and USB-BOB
- Replies: 79
- Views: 4083
Re: OPCON and USB-BOB
Perfect, the way to build a commander Kirk desk
Uwe
Uwe
- Tue Feb 20, 2024 4:24 pm
- Forum: Public Beta CNC Software Testing, Discussion and Feedback
- Topic: Tool table in the report
- Replies: 3
- Views: 166
Re: Tool table in the report
Make a backup of the PLC before changing it, so you can go back to the last working version.
Uwe
Uwe
- Tue Feb 20, 2024 4:18 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Tool offsets Lathe
- Replies: 4
- Views: 243
Re: Tool offsets Lathe
If you have set Z Ref with the probe, manual Z measure at another Z position than that of the probe will not work. If I have to set Z for a tool and do not want to use the probe while a part ist in the spindle, I make sure the tool is selected and drive it to part Z 0. Than I correct its Z offset so...
- Mon Feb 19, 2024 11:58 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Safe Spindle Temperature?
- Replies: 23
- Views: 1068
Re: Safe Spindle Temperature?
Maybe you can find a labyrinth ring seal in the right size, they could take more rpm with less friction.
Uwe
Uwe
- Mon Feb 19, 2024 5:41 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Safe Spindle Temperature?
- Replies: 23
- Views: 1068
Re: Safe Spindle Temperature?
Without special equipment, brake cleaner spray and compressed air.
Will make a funny mess
Uwe
Will make a funny mess
Uwe
- Mon Feb 19, 2024 4:11 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Safe Spindle Temperature?
- Replies: 23
- Views: 1068
Re: Safe Spindle Temperature?
If you mean leaving the bearings on the spindle and in the head, ok. But you must remove the spindle to wash out all old grease.
I doubt it will be the seal, but also NBU15 will lubricate the seal better than cheap grease.
Uwe
I doubt it will be the seal, but also NBU15 will lubricate the seal better than cheap grease.
Uwe
- Mon Feb 19, 2024 2:34 pm
- Forum: Public Beta CNC Software Testing, Discussion and Feedback
- Topic: OPCON and USB-BOB
- Replies: 79
- Views: 4083
Re: OPCON 15374
5.08 with Acorn Six, no problems with OPCON.
Did you follow the instructions?
Read which Com port, set parameter in CNC12 and it runs.
Uwe
Did you follow the instructions?
Read which Com port, set parameter in CNC12 and it runs.
Uwe
- Mon Feb 19, 2024 8:48 am
- Forum: Centroid Acorn CNC Controller
- Topic: Tool offsets Lathe
- Replies: 4
- Views: 243
Re: Tool offsets Lathe
The width of the probe is only for auto measure ZX, so after measuring Z the CNC knows the center of the probes width. Measuring drills in X with the probe is a "bad habit", because if the drill edge is not exactly set in height you get wrong values, set X0 of the toolholder with a dial in...