Search found 77 matches
- Wed Feb 24, 2021 12:29 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: All In One bench test
- Replies: 46
- Views: 13000
Re: All In One bench test
Marty, As I stated. The max RPM is set to 3000. I'm using a Fluke 27. One of the best you could buy at one time.
- Tue Feb 23, 2021 8:56 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: All In One bench test
- Replies: 46
- Views: 13000
Re: All In One bench test
Tom, I have an All In One. The spindle encoder is attached to the board but I have not run any wires to the VFD. Bob
- Tue Feb 23, 2021 12:15 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: All In One bench test
- Replies: 46
- Views: 13000
All In One bench test
Got a small problem. I'm doing the spindle voltage part of the bench test. When I hit alt-S for S500 I get a reading of 3.35 DCV. When I input it and continue I get an error message Invalid voltage. I checked and the max spindle speed is set at 3000rpm. What am I doing wrong here. Thanks Bob L
- Mon Feb 22, 2021 3:16 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: DB-9 Connector
- Replies: 7
- Views: 2863
Re: DB-9 Connector
Now the bad news. The plastic case is to wide to fit them on the All In One side by side. So chucked the case and wrapped them with rubber tape and ty-wraped the wire end. Still beats soldering them. replaced the screws with 4-40X3/8" long (Home Puke). Job done. Bob L
- Mon Feb 15, 2021 4:41 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Air pressure proving switch on Bridgeport V2XT or Boss
- Replies: 7
- Views: 2781
Re: Air pressure proving switch on Bridgeport V2XT or Boss
Got the picture. Thanks
- Mon Feb 15, 2021 3:21 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Air pressure proving switch on Bridgeport V2XT or Boss
- Replies: 7
- Views: 2781
Re: Air pressure proving switch on Bridgeport V2XT or Boss
Let me ask a question. What exactly is a spindle fault? I mean as far as I know it just turns. So what exactly could go wrong with the spindle? Thanks, Bob L
- Thu Feb 11, 2021 8:53 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Only 1 limit switch
- Replies: 14
- Views: 5287
Re: Only 1 limit switch
Craig, It's a no brainer. Two heavy duty SEALED Honeywell push switches (E-Bay dirt cheap). All ya need is a stop on the casting below the table at the center of travel. Mount your switches on the table just short of travel in each direction. They don't have to be adjustable and your done. If ya nee...
- Wed Feb 10, 2021 10:32 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Air pressure proving switch on Bridgeport V2XT or Boss
- Replies: 7
- Views: 2781
Re: Air pressure proving switch on Bridgeport V2XT or Boss
Now were talking! Thanks
- Wed Feb 10, 2021 8:45 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Air pressure proving switch on Bridgeport V2XT or Boss
- Replies: 7
- Views: 2781
Re: Air pressure proving switch on Bridgeport V2XT or Boss
You wouldn't like to explain that in English would ya?
- Wed Feb 10, 2021 7:15 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Bridgeport V2XT Limit switches
- Replies: 3
- Views: 1829
Re: Bridgeport V2XT Limit switches
Limit switches replaced Marty. I'm $200 clams poorer but they work and at the end of the day. That's all you want. Bob L