The system has been updated to 4.62. The problem as stated before remains the same.
Any ideas???
Search found 63 matches
- Mon Mar 08, 2021 10:29 pm
- Forum: Centroid Acorn CNC Controller
- Topic: back to basics
- Replies: 12
- Views: 4189
- Mon Mar 08, 2021 9:54 pm
- Forum: Centroid Acorn CNC Controller
- Topic: back to basics
- Replies: 12
- Views: 4189
Re: back to basics
Yes , the red goes to input 8
The red wire is twisted to the black wire to simulate the esop connection to show the simplify the connection. I used the mushroom button on the spindle to test but its out view so I simply showed the connection in the picture
The red wire is twisted to the black wire to simulate the esop connection to show the simplify the connection. I used the mushroom button on the spindle to test but its out view so I simply showed the connection in the picture
- Mon Mar 08, 2021 6:45 pm
- Forum: Centroid Acorn CNC Controller
- Topic: back to basics
- Replies: 12
- Views: 4189
back to basics
I decided to upgrade motor tp clear path and build a next control box. With a clean sheet I fired it up and now can I not get the board to respond to an Estop What I know: 1) the only connection to this board at present is the Estop. It is a NC switch which is working as verified by the on/off conti...
- Fri Jul 03, 2020 10:35 am
- Forum: Centroid Acorn CNC Controller
- Topic: KP-3 problem
- Replies: 10
- Views: 3408
Re: KP-3 problem
I did read the post. It was not clear that the board should be clipped from probes previously shipped. The instruction that came with the board emphasized that that the board was not be removed. Before clipping this thing I need to ask: 1) If you do not have spindle control set up what are the probe...
- Fri Jul 03, 2020 9:14 am
- Forum: Centroid Acorn CNC Controller
- Topic: KP-3 problem
- Replies: 10
- Views: 3408
Re: KP-3 problem
1) Latest report attached
2) The " flipper board" is there.
Thanks Guys
2) The " flipper board" is there.
Thanks Guys
- Thu Jul 02, 2020 7:40 pm
- Forum: Centroid Acorn CNC Controller
- Topic: KP-3 problem
- Replies: 10
- Views: 3408
Re: KP-3 problem
I attached what you have requested.
- Thu Jul 02, 2020 11:15 am
- Forum: Centroid Acorn CNC Controller
- Topic: KP-3 problem
- Replies: 10
- Views: 3408
KP-3 problem
The kp3 probe is disabling the MPg control wheel when the KP3 is plug in. When attempting to probe the error message says that the probe is tripped. 1) Running 4.5 2) The Ctl_ i Input screen shows a green dot for input 6 and 7 3) The Wizzard /probe has the probe-KP3 selected and defaults unchanged. ...
- Wed Jun 24, 2020 9:25 am
- Forum: Centroid Acorn CNC Controller
- Topic: H10 output pins
- Replies: 4
- Views: 2032
Re: H10 output pins
Thank up Dr Locke. That was exactly the info I was looking for.
- Tue Jun 23, 2020 4:07 pm
- Forum: Centroid Acorn CNC Controller
- Topic: H10 output pins
- Replies: 4
- Views: 2032
H10 output pins
I am trying to connect the output pins on the H10 connector to a clear path MCPV motor without going through the relays. When I assign a function to one of the outputs in the wizard and enable the pin with the M94 command I see I can see the change in state on the led on the board but my multimeter ...
- Sat Apr 25, 2020 9:07 pm
- Forum: Centroid Acorn CNC Controller
- Topic: maco writeing resorces
- Replies: 1
- Views: 1328
maco writeing resorces
Does anyone have a good resource to teach a newbe how to write macros? There are a lot of examples around but I would like to start at the beginning.
Thanks
Thanks