Search found 3095 matches
- Wed Apr 28, 2021 4:12 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: High Idle Current
- Replies: 14
- Views: 4016
Re: High Idle Current
From the looks of the setup, I would guess it's running through the original miter gears and the stock Acme screw. If you really want this to work well, replace the acme screw with a ballscrew and drive it directly and not through the miter gear set.
- Wed Apr 28, 2021 12:17 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Homing Problem
- Replies: 5
- Views: 1704
Re: Homing Problem
Within my Alphacam I have a large tool library where I select my tools and generate the programs but need some advice regarding the tool library in CNC12. i.e. does it have to match up exactly with my Alphacam tool library data? If so can this be imported directly or does it have to be done the lon...
- Tue Apr 27, 2021 11:17 am
- Forum: Centroid Acorn CNC Controller
- Topic: Spindle degree readout on lathe (Resolved)
- Replies: 5
- Views: 1529
Re: Spindle degree readout on lathe
I would think you could set it up as a manual axis using the spindle encoder - I don't think you can actually configure it as a C axis. F1 Setup/F2 Motor set up axis 3 with label "M", revs/in as 1, and encoder counts/rev with whatever your spindle encoder has. Parameter 93 (properties for ...
- Mon Apr 26, 2021 6:47 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: High Idle Current
- Replies: 14
- Views: 4016
Re: High Idle Current
You need to tune your axis for the max feedrate you have set on the motors page. For the knee, I'm assuming "air assist" is a pneumatic cylinder counterbalance. Increase the pressure on that to reduce the idle current.
- Mon Apr 26, 2021 6:09 pm
- Forum: Centroid Acorn CNC Controller
- Topic: retro fit Laguna/RichAuto
- Replies: 96
- Views: 23952
Re: retro fit Laguna/RichAuto
Either noise or vibration is causing false triggers on the limit switch.
- Mon Apr 26, 2021 4:11 pm
- Forum: Centroid Acorn CNC Controller
- Topic: proLIGHT 2000 Conversion to Acorn
- Replies: 43
- Views: 14739
Re: proLIGHT 2000 Conversion to Acorn
Min and max are for the spindle rpms, not the motor. If you set max to 10,000rpm, and you issue a M3 S10000, then the analog out will be 10V. It's up to your motor controller (VFD) to decide what to do with that 10V.
- Mon Apr 26, 2021 2:51 pm
- Forum: Centroid Acorn CNC Controller
- Topic: 4th axis
- Replies: 14
- Views: 5473
Re: 4th axis
Remember, that's for an AllIn1DC not an Acorn, but it should give you something to get started with.
- Mon Apr 26, 2021 1:19 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Send key presses to MPU from PLC code
- Replies: 5
- Views: 1829
Re: Send key presses to MPU from PLC code
You would need a keyboard emulator that takes an external switch closure and sends an F8 keyboard character to Windows.
Something like this: https://www.sorion-group.com/products/p ... xis-kbdem/
Something like this: https://www.sorion-group.com/products/p ... xis-kbdem/
- Mon Apr 26, 2021 7:49 am
- Forum: Centroid Acorn CNC Controller
- Topic: 4th axis
- Replies: 14
- Views: 5473
Re: 4th axis
Here's how I have my rotary connected to my AllIn1DC. I also modified my PLC program to check the clamp pressure feedback after a short delay.
viewtopic.php?f=64&t=2572&p=18359&hilit ... mer#p18359
viewtopic.php?f=64&t=2572&p=18359&hilit ... mer#p18359
- Sun Apr 25, 2021 9:21 am
- Forum: Centroid Acorn CNC Controller
- Topic: Power supply for acorn (Resolved)
- Replies: 2
- Views: 833
Re: Power supply for acorn
A separate supply for the Acorn is recommended to reduce the amount of electrical noise that may cause problems with the Acorn.