Search found 19 matches
- Mon Jan 17, 2022 3:04 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: $th Axis install, errors galore <answered>
- Replies: 10
- Views: 2590
Re: $th Axis install, errors galore
Thanks guys, I am going to give it a try tonight if they ever plow the roads, and I can make it home.
- Sat Jan 15, 2022 3:09 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: $th Axis install, errors galore <answered>
- Replies: 10
- Views: 2590
$th Axis install, errors galore <answered>
Wired up the 4th axis, Set the encoder counts, eneabled it, and all my axis became rogue, moving Y caused X to take off and no other axis worked. I added my config to this post
I was unable to locate a manual for or much help online for the DC1
Thanks,
Paul
I was unable to locate a manual for or much help online for the DC1
Thanks,
Paul
- Fri Jan 14, 2022 12:39 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Spindle Encoder Differential Error
- Replies: 3
- Views: 1011
- Thu Jan 13, 2022 11:32 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Spindle Encoder Differential Error
- Replies: 3
- Views: 1011
Spindle Encoder Differential Error
First of this machine is a Bridgeport Explorer X26. The spindle encoder had 3 wires. My guess on colors was Red + Blk - Wht "A" signal. Once wired and enabled in the parameters, I received an encoder differential error. One, did I wire it correctly, two what did I goof up on?
Thanks!!
Thanks!!
- Tue Jan 04, 2022 10:39 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Probe unable to detect surface
- Replies: 3
- Views: 1002
Re: Probe unable to detect surface
Swissi,
Thanks!! its always the simple things that kick you. Appreciate the help.
~Visco
Thanks!! its always the simple things that kick you. Appreciate the help.
~Visco
- Sun Jan 02, 2022 10:49 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Probe unable to detect surface
- Replies: 3
- Views: 1002
Probe unable to detect surface
Initial Probe Setup.
When I go to probe bore. It travels, hits the surface, backs up (X3 Times). Then throws error "Probe unable to detect surface." If it did not detect the surface, what stopped it
Thanks in Advance.
~P
When I go to probe bore. It travels, hits the surface, backs up (X3 Times). Then throws error "Probe unable to detect surface." If it did not detect the surface, what stopped it
Thanks in Advance.
~P
- Fri Nov 26, 2021 4:10 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Z Axis Home issue <resolved>
- Replies: 4
- Views: 1131
Re: Z Axis Home issue
FIXED! Thanks
@cncsnw I had my encoders set at 8000, they were supposed to be 20,000
@cncsnw I had my encoders set at 8000, they were supposed to be 20,000
- Fri Nov 26, 2021 3:51 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Z Axis Home issue <resolved>
- Replies: 4
- Views: 1131
Re: Z Axis Home issue
I should have mentioned above. It is seeing encoder counts and I confirmed they are correct + and -. I have the encoders at 8000 which seems accurate if I do one full turn of the motor.
- Fri Nov 26, 2021 2:46 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Z Axis Home issue <resolved>
- Replies: 4
- Views: 1131
Z Axis Home issue <resolved>
This is a new install/upgrade. I have enabled to home switches to: Home Switch When I press cycle start I get: 407 Z+ limit (#50006) tripped 302 Movinq... 340 Z+ limit (#50006) cleared 302 Movinq... 457 Unable to find home 338 Job cancelled It says it found the Z+ home switch then moves off of it an...