Search found 169 matches
- Tue Oct 24, 2023 12:47 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Air Blower installation
- Replies: 8
- Views: 570
Re: Air Blower installation
Then let me rephrase the question. How can I control more than one relay with one command? If I can do this I will parallel the spindle control with the air blower control and all of the existing tool paths that I have will work without modification.
- Tue Oct 24, 2023 10:48 am
- Forum: Centroid Acorn CNC Controller
- Topic: Air Blower installation
- Replies: 8
- Views: 570
Air Blower installation
I have installed an air blower system on my machine. It operates as it should when I use the control panel to turn the output (No 5) on and off. This tells me that all is well with the. wiring, the relay, and the Acorn. How do I now get the post processor to insert the code to turn it on and off. Be...
- Mon May 01, 2023 6:33 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Using Z zero plate with pendant
- Replies: 5
- Views: 417
Re: Using Z zero plate with pendant
Thanks for the help
- Mon May 01, 2023 1:38 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Using Z zero plate with pendant
- Replies: 5
- Views: 417
Using Z zero plate with pendant
I see where the Z Zero macro is now a part of the VCP. How do I program one of the aux keys on my pendant to start the Z Zero routine?
- Sat Mar 25, 2023 1:56 pm
- Forum: Centroid Acorn CNC Controller
- Topic: It's me again, Clearpath losing/gaining steps <resolved, loose pulley>
- Replies: 15
- Views: 1901
Re: It's me again, Clearpath losing/gaining steps
Clearpath has a good write up on the subject of clamping Here
https://teknic.com/files/downloads/Secu ... Shafts.pdf
- Fri Mar 24, 2023 3:07 pm
- Forum: Centroid Acorn CNC Controller
- Topic: best setting for C86 board
- Replies: 0
- Views: 927
best setting for C86 board
I have just installed the C-86 board on my Acorn. Apparently there are two settings that have to do with the alarm system on the clearpath motors. Each axis has a "Hard - Soft" setting that determins whether the motor reacs to hardware of software changes. There is also an Acorn on off set...
- Fri Mar 24, 2023 7:07 am
- Forum: Centroid Acorn CNC Controller
- Topic: can't get wizard to change drive type
- Replies: 6
- Views: 692
Re: can't get wizard to change drive type
I took the computer home, cleaned all of the centroid program material off, downloaded a fresh install from the web, re-installed it and now everything seems to work like it should. That box you show circled in your message was not appearing in the first install.
- Wed Mar 22, 2023 1:08 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Upgrade problem will not flash the program in Acorn
- Replies: 2
- Views: 312
Upgrade problem will not flash the program in Acorn
I tried to install the latest version of CNC 12 V4.82. When I first ran it it tried to flash the EProm (or whatever non volatile memory is used) in the Acorn board. It failed and told me so on the screen. I shut down the program and the acorn then re-started. When it re-started it went directly to t...
- Wed Mar 22, 2023 6:36 am
- Forum: Centroid Acorn CNC Controller
- Topic: can't get wizard to change drive type
- Replies: 6
- Views: 692
Re: can't get wizard to change drive type
I don't understand why Centroid would put a whole section into their software that does not do anything. Also why can I not change the selection? Is that common?
- Tue Mar 21, 2023 10:45 am
- Forum: Centroid Acorn CNC Controller
- Topic: can't get wizard to change drive type
- Replies: 6
- Views: 692
can't get wizard to change drive type
I am installing the C86 board in my centroid acorn system. I have upgraded the program to the latest and now I am trying to change the drive type from the default to Clearpath. The program will not accept it. It says that the change has been done and re-cycle the program. I have tried multiple times...