maybe , probably. depends if you bury the spindle going full speed on all axes at the same time...with every accessories on full blast.
do you plan on doing that? if not, you'll be fine.
Search found 7334 matches
- Fri Apr 19, 2024 5:32 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Centroid acorn router machine build
- Replies: 14
- Views: 778
- Fri Apr 19, 2024 3:16 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Instructional video
- Replies: 5
- Views: 210
Re: Instructional video
post a fresh report.zip so we can see your setup. otherwise we would just be guessing at the issue
- Thu Apr 18, 2024 7:08 pm
- Forum: Centroid Hickory CNC Controller
- Topic: Breaking news! Delta B3A ethercat drive is now running with Hickory and we are doing final tests on a machine
- Replies: 7
- Views: 1382
Re: Breaking news! Delta B3A ethercat drive is now running with Hickory and we are doing final tests on a machine
One thing that I'm wondering. The PID (centroid side) is that purely for delay in drives or is that also a PID position-wise (running over the Delta PID)? Delta takes care of the PID, EtherCat runs in position mode. Centroid Drive Delaty Autotune is only for the Drive Delay calculation and has noth...
- Thu Apr 18, 2024 7:05 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Wizard data disappearing
- Replies: 4
- Views: 207
Re: Wizard data disappearing
Greetings, I'm having a problem with CNC12 Acorn Router V5.08. It is similar to a problem I had with the previous version which was V4.8. With V5.08, the Wizard page for Axis Squaring resets and loses my settings. It first happened last week. All my macros were off. Once I discovered that the Axis ...
- Thu Apr 18, 2024 7:04 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Wiring up home switches
- Replies: 2
- Views: 129
Re: Wiring up home switches
nope, you can do either, users that want to save on input use HomeAll other that don't using the individual home input definitions
- Thu Apr 18, 2024 7:02 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Delta ASDA-B2 ACORN WIRING INFORMATION
- Replies: 28
- Views: 747
Re: Delta ASDA-B2 ACORN WIRING INFORMATION
What exact model ASDA-B2 drives do you have? It will say on the nameplate sticker. Please post a picture of the connector and nameplate sticker if you can. I am curious because all of Delta's documentation for ASD-B2-xxxx-B (standard spec) drives shows a 44 pin CN1 connector. The ASD-B2-xxxx-F spec...
- Thu Apr 18, 2024 6:19 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Touch probe
- Replies: 20
- Views: 960
Re: Touch probe
ok sounds like we are taking about probing and not digitizing )
sounds like you just need to locate these features relative to another point on the object. then you will know where to place the geometry in the cad model. this is pretty easy.
sounds like you just need to locate these features relative to another point on the object. then you will know where to place the geometry in the cad model. this is pretty easy.
- Thu Apr 18, 2024 2:48 pm
- Forum: Public Beta CNC Software Testing, Discussion and Feedback
- Topic: Centroid Operator Control Panel Interface Board: USB-BOB
- Replies: 43
- Views: 1802
Re: Centroid Operator Control Panel Interface Board: USB-BOB
try to keep the kit under $250, its tough these days!
- Thu Apr 18, 2024 2:38 pm
- Forum: Public Beta CNC Software Testing, Discussion and Feedback
- Topic: CNC12 v5.1 RC#6 Mill, Lathe, Router, Plasma RC5 now available for download and testing.
- Replies: 5
- Views: 249
Re: CNC12 v5.1 RC#6 Mill, Lathe, Router, Plasma RC5 now available for download and testing.
SIGMA 2 SYSTEM ??? acorn centroid with delta asda-b2 wiring system problem . went cnc 12 and acorn is open , and I power up the the motor drive the x and z (only 2 axes are powered up for now) the motor start moving by it self. What rough with acorn??? hi, disconnect all but one delta drive from th...
- Wed Apr 17, 2024 3:39 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Multi Spindle CNC Router control options
- Replies: 18
- Views: 513
Re: Multi Spindle CNC Router control options
you'll have to try it or ask the guy who wrote the post! i don't use Fusion.