Search found 3853 matches
- Sun Oct 20, 2019 7:55 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Loading from a USB CNC10
- Replies: 4
- Views: 2746
Re: Loading from a USB CNC10
It will help to set Machine Parameter 4 to a value of 5.0, so that it shows the "advanced" version of the file menu, as well as automatically importing files loaded from outside the control. Not all USB devices will work with the Linux system. If you can find one, use a SanDisk Cruzer of 1...
- Sun Oct 20, 2019 2:41 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Travel / Limit / Home switches
- Replies: 15
- Views: 5412
Re: Travel / Limit / Home switches
Sounds good. Be aware that the software limits won't work perfectly if some other issue (e.g. the noise resulting from powering the drives with 240VAC) is causing you to lose position. At 0.002" per pass, it would take quite a while before you lose position to the point that you overrun the lim...
- Sun Oct 20, 2019 2:37 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: M-15 Training in Minnesota (RESOLVED)
- Replies: 41
- Views: 10395
Re: M-15 Training in Minnesota
Alternately, if the hard drive in the "mill" control is still good, you could either install it in the "router" control (which is on the mill) and get the correct configuration and parameters that way. You would just need to re-enter the software unlock codes from the router cont...
- Sun Oct 20, 2019 12:30 am
- Forum: Centroid Acorn CNC Controller
- Topic: Travel / Limit / Home switches
- Replies: 15
- Views: 5412
Re: Travel / Limit / Home switches
It is a bad idea to try to use the same sensor or switch as both the plus and minus limit. The control software does not attempt to determine which direction an axis might have been moving then the switch came to be tripped: it just prohibits moving towards a tripped switch. So if you designate the ...
- Sun Oct 20, 2019 12:22 am
- Forum: Centroid Acorn CNC Controller
- Topic: Rotary limit switch, kind-of
- Replies: 2
- Views: 1277
Re: Rotary limit switch, kind-of
M105/M106 or M115/M116. See Chapter 13 of the manual. See also http://www.cncsnw.com/AdvancedMacroProgramming.htm
- Sat Oct 19, 2019 6:45 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: M-15 Training in Minnesota (RESOLVED)
- Replies: 41
- Views: 10395
Re: M-15 Training in Minnesota
Assuming we are still talking about K4849, then WildBilly's previous posts indicate that the machine has no real limit switches installed. In this case, the only way to run is with the limits defeated via the DIP switches. At some point, pulling a Report and posting the resulting "CNC7CFG.TXT&q...
- Sat Oct 19, 2019 6:32 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: 13139 console
- Replies: 2
- Views: 1654
Re: 13139 console
If you are looking for just the black sheet metal box, I have one that you can have for $200.
- Sat Oct 19, 2019 6:20 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Travel / Limit / Home switches
- Replies: 15
- Views: 5412
Re: Travel / Limit / Home switches
Maybe Keith or Marty can jump in here. My experience is entirely with closed-loop systems (Oak, All-in-one DC and their predecessors). The question: can you have one input, with three normally-closed limit switches in series, that is the limit (and home) for X-, Y+ and Z+; then have a second input, ...
- Fri Oct 18, 2019 2:52 am
- Forum: Centroid Acorn CNC Controller
- Topic: toool offset question
- Replies: 5
- Views: 2463
Re: toool offset question
Or, if the tool is already in the spindle and you just want to reactivate the offsets:
G43 H4
G43 H4
- Wed Oct 16, 2019 12:34 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: How to disable comp look ahead?
- Replies: 1
- Views: 1234
Re: How to disable comp look ahead?
You cannot "disable lookahead" in cutter comp. Cutter comp needs to look ahead at least one move in order to do its job. You can change the number of lines that it looks ahead, via Parameter 99. That has to do with interference checking, and may apply to your situation if you have moves th...