Search found 65 matches
- Thu Mar 26, 2020 7:19 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Analog voltage increases when VFD is connected
- Replies: 89
- Views: 31167
Re: Analog voltage increases when VFD is connected
How hard can it be for centroidcnc to put a voltage regulator on the board ?
- Thu Mar 26, 2020 7:04 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Analog voltage increases when VFD is connected
- Replies: 89
- Views: 31167
Re: Analog voltage increases when VFD is connected
Situation report I had another weg here but different model (older with far less functions) and it works. No voltage rising (it stays 0.12 volts) when all is connected. I will put this one inside the box to see but I believe that it will work. I will check all.the parameters on the newer one to see ...
- Thu Mar 26, 2020 6:59 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Analog voltage increases when VFD is connected
- Replies: 89
- Views: 31167
- Thu Mar 26, 2020 5:14 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Analog voltage increases when VFD is connected
- Replies: 89
- Views: 31167
Re: Analog voltage increases when VFD is connected
This is the second VFD. Same model.
I will try one more.
The voltage across the VFD analog ports reads 0.0V with acorn disconnected
I will try one more.
The voltage across the VFD analog ports reads 0.0V with acorn disconnected
- Thu Mar 26, 2020 5:00 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Analog voltage increases when VFD is connected
- Replies: 89
- Views: 31167
Re: Analog voltage increases when VFD is connected
Go into MDI and type M3 S0, cycle start Then type M5 cycle start Then read the voltage. What is the voltage? There are NO adjustments to the analog output. Did you consider what Tom suggested earlier? (Looks like it needs two power supplies) https://www.amazon.com/Isolation-S-10V10V-Quantities-Volt...
- Thu Mar 26, 2020 4:32 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Analog voltage increases when VFD is connected
- Replies: 89
- Views: 31167
Re: Analog voltage increases when VFD is connected
I'm running ABB ACS-355 drives on my machines. Updates Taking the VFD out of the enclosure had some Improvement The capacitor does not help The strange thing With acorn powered up but cnc12 down, voltage remains near zero When I power up cnc12 software, voltage goes crazy to 1.7-2.0 volts. https://...
- Sun Mar 22, 2020 2:54 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Analog voltage increases when VFD is connected
- Replies: 89
- Views: 31167
Re: Analog voltage increases when VFD is connected
So what is a good, known VFD ? Teco is a good one ?
- Sat Mar 21, 2020 4:09 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Analog voltage increases when VFD is connected
- Replies: 89
- Views: 31167
Re: Analog voltage increases when VFD is connected
I'm guessing its AC noise the VFD is generating on terminals where there should be only DC voltage present. A small capacitor ACROSS the analog input terminals might block this noise. A 100nf (0.1 micro Farad) capacator between the analog input terminal and analog common terminal MAY make a differe...
- Sat Mar 21, 2020 1:23 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Analog voltage increases when VFD is connected
- Replies: 89
- Views: 31167
Re: Analog voltage increases when VFD is connected
I will try a brand new VFD (exact same model) and another VFD model to see
- Sat Mar 21, 2020 1:14 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Analog voltage increases when VFD is connected
- Replies: 89
- Views: 31167
Re: Analog voltage increases when VFD is connected
My old board was working so well. I don't know why this is happening