Search found 2181 matches
- Sat Mar 16, 2024 8:44 am
- Forum: Centroid Acorn CNC Controller
- Topic: No motor movement
- Replies: 7
- Views: 329
Re: No motor movement
Connect those LeadShine (clone) drives to the DB25 connector and make sure that you do not connect to the enable pin on the drive
- Sun Mar 10, 2024 9:53 am
- Forum: Centroid Acorn CNC Controller
- Topic: Macro Help For Floating Z- Soft Limit (Resolved to keep bit from diving into spoilboard)
- Replies: 6
- Views: 276
Re: Macro Help For Floating Z- Soft Limit
Why not use the existing "Machining Envelope" feature?
- Sat Mar 09, 2024 9:25 am
- Forum: Centroid Acorn CNC Controller
- Topic: CNC CONTROL SUGGESTIONS
- Replies: 28
- Views: 901
Re: CNC CONTROL SUGGESTIONS
Yours is a pretty straightforward tangential cutter application. As long as you have a CAM program that can output the C axis positions, I see no obstacles. There are numerous options for customization with the Centroid system. Both virtual (onscreen) and physical buttons. Here's one I did a few yea...
- Wed Mar 06, 2024 10:07 pm
- Forum: Centroid Acorn CNC Controller
- Topic: 24v input issue <resolved, short to ground by foil>
- Replies: 14
- Views: 437
Re: 24v input issue
It looks like you are connecting to a 24v com terminal on the power block. The 24v(+) terminals are the 2 on the far right
- Thu Feb 22, 2024 10:12 pm
- Forum: Centroid Acorn CNC Controller
- Topic: MDI Spindle Voltage Incorrect
- Replies: 5
- Views: 249
Re: MDI Spindle Voltage Incorrect
Have you tried adding a 0.1mfd capacitor across the Acorn analog terminals?
- Thu Feb 22, 2024 8:57 am
- Forum: Centroid Acorn CNC Controller
- Topic: MDI Spindle Voltage Incorrect
- Replies: 5
- Views: 249
Re: MDI Spindle Voltage Incorrect
If you wish your analog voltage to be linear, set the wizard rpm minimum to zero. Then set your desired minimum speed in the VFD parameters (Htz Min)
- Tue Feb 20, 2024 10:42 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Strange noise issue.
- Replies: 5
- Views: 246
Re: Strange noise issue.
Shopvacs and their PVC hoses are some of the worst static generators out there. Look this over, it may help
- Thu Feb 15, 2024 11:00 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Need travel consistency but its not working as expected <800 steps per rev too low>
- Replies: 18
- Views: 769
Re: Need travel consistency but its not working as expected <800 steps per rev too low>
Set your ClearPath motors to 3200 steps per rev
- Sun Feb 11, 2024 9:08 am
- Forum: Centroid Acorn CNC Controller
- Topic: new here
- Replies: 14
- Views: 505
Re: new here
is that the only solution No. You can use NPN Normally Open (NO) sensors in parallel. NO sensors are usually cheaper and for the purposes of homing or limits on a homebuilt router they will perform every bit as good as the NC versions. The only downside is that a NO sensor will not show as tripped ...
- Fri Feb 09, 2024 9:13 am
- Forum: Centroid Acorn CNC Controller
- Topic: Software Feature Request: spindle speed adjustment
- Replies: 6
- Views: 322
Re: Software Feature Request: spindle speed adjustment
Try using the WPG Pendant's wheel. Works as fast (or as slow) as you desire.