Yes, "THC Installed" is set to Yes and Green.
Tom
Search found 33 matches
- Wed Sep 14, 2022 3:38 pm
- Forum: Acorn CNC Plasma
- Topic: A Question on Ohmic Sensing
- Replies: 7
- Views: 1329
- Wed Sep 14, 2022 2:04 pm
- Forum: Acorn CNC Plasma
- Topic: A Question on Ohmic Sensing
- Replies: 7
- Views: 1329
A Question on Ohmic Sensing
I've wired the ohmic sensor as shown in S15108, defined Output4 as Ohmic Enabled and conducted a successful continuity check from the tip of the torch to T In on the TX board but when I touch the tip to ground I do not see the Plasma T IN led turn green as described on page 15 of the Plasma Users Ma...
- Wed Aug 31, 2022 12:18 pm
- Forum: Acorn CNC Plasma
- Topic: A few questions on Duramax 180 torch
- Replies: 7
- Views: 1267
Re: A few questions on Duramax 180 torch
Thanks for the continuing input. I appreciate it. Regarding the touch off question. I understand the circuitry but I'm trying to understand the physical connections. I found an image online that I think answers my question. The attached image shows a wire - outside of any existing wiring in the torc...
- Wed Aug 31, 2022 9:51 am
- Forum: Acorn CNC Plasma
- Topic: A few questions on Duramax 180 torch
- Replies: 7
- Views: 1267
Re: A few questions on Duramax 180 torch
Hi, and thanks for giving me some information but it doesn’t answer all my questions. 1 – I understand the principal of the ohmic sensor and I have seen the schematic and how the signal comes from the tip, through the relay board then to the THC-TX board but how does the signal physically get there?...
- Mon Aug 29, 2022 10:41 am
- Forum: Acorn CNC Plasma
- Topic: A few questions on Duramax 180 torch
- Replies: 7
- Views: 1267
A few questions on Duramax 180 torch
I am in the process of upgrading my old DIY plasma cutter with an Acorn board, Centroid THC, Hypertherm Powermax 45 plasma cutter with a Hypertherm Mechanized Duramax 180 deg Lock Torch but I have a few questions. 1- I understand the concept of ohmic sensor touch-off but I don’t understand how it’s ...
- Wed Aug 17, 2022 12:58 pm
- Forum: Acorn CNC Plasma
- Topic: An embarrassing question to ask
- Replies: 2
- Views: 854
An embarrassing question to ask
I purchased and received a software license for Acorn Plasma "Pro" CNC Software but I can't find where to download the software itself.
Again, any help would be appreciated.
Tom
Again, any help would be appreciated.
Tom
- Wed Aug 17, 2022 12:50 pm
- Forum: Acorn CNC Plasma
- Topic: Need an explanation of touch off
- Replies: 4
- Views: 1019
Re: Need an explanation of touch off
Thanks for all the replies. I think I understand it now.
Tom
Tom
- Tue Aug 16, 2022 11:01 am
- Forum: Acorn CNC Plasma
- Topic: Need an explanation of touch off
- Replies: 4
- Views: 1019
Need an explanation of touch off
I've read the post and watched videos but I'm still confused as to what torch touch off is. Can someone give me an explanation of exactly what it is and the pros and cons of using it. The old plasma cutter I'm rebuilding has a float switch on the Z axis to establish torch height. Use both, only one,...
- Fri Aug 12, 2022 10:16 am
- Forum: Acorn CNC Plasma
- Topic: A couple of questions about converting to Centroid
- Replies: 3
- Views: 1168
Re: A couple of questions about converting to Centroid
Hi Shawn, Thanks for the reply. What you said makes sense. Do you have any idea of the current draw for the DM542Ts so I can properly size the 5VDC supply? Also, you recommend not tying the ground of the (24V or 48V) motor power supply to the Acorn 24/5V and logic 5V together. Is that right? Thanks ...
- Thu Aug 11, 2022 6:22 pm
- Forum: Acorn CNC Plasma
- Topic: A couple of questions about converting to Centroid
- Replies: 3
- Views: 1168
A couple of questions about converting to Centroid
I’m reconfiguring my current DYI plasma cutter with the Centroid components as shown on their web site. I'm planning on using my existing Stepper Online DM542T stepper drivers (at 24VDC) and would like any info on how they perform with the Centroid components. I'd like to use then to save on cost. M...