Search found 99 matches
- Tue Jun 09, 2020 10:32 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Chinese hsd spindle
- Replies: 89
- Views: 34040
Re: Chinese hsd spindle
Drive shows rdy indicator,, but when signal sent, nothing happen,, is this drive need 24v to enable it?
- Tue Jun 09, 2020 12:23 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Chinese hsd spindle
- Replies: 89
- Views: 34040
Re: Chinese hsd spindle
And yes,, oc4 was previously attempt use to power some relay to make swicth for hand router that i use for the spindle,,and it doesn't work,if u remember few years ago i do have ask u in the forum for that matter,, i think that was a cause,short circuit, maybe,,i thought output is 24v,,
- Tue Jun 09, 2020 12:14 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Chinese hsd spindle
- Replies: 89
- Views: 34040
Re: Chinese hsd spindle
Ok thanks for the advise, i will work on that , i just finish hook up the wire to control the drive,, the wierd is, when m4 s100 is cycle, and oc 5 is power on relay spindle do not run,, and wire for relay oc3 receive 24v also,, is that normal? Or setting on the driver was set incorrect, or wire pro...
- Tue Jun 09, 2020 10:36 am
- Forum: Centroid Acorn CNC Controller
- Topic: Chinese hsd spindle
- Replies: 89
- Views: 34040
Re: Chinese hsd spindle
The Input/Output screen shot shows that M3 should trigger output 3 and that M4 should trigger output 6 M3 is trigger output 3, spin foward, m4 is trigger output 5 spind reversed, is that what u means? So what happens to output 4,, Yes and you have Output four set for Mist. M7 turns it on, M9 turns ...
- Tue Jun 09, 2020 10:30 am
- Forum: Centroid Acorn CNC Controller
- Topic: Chinese hsd spindle
- Replies: 89
- Views: 34040
Re: Chinese hsd spindle
That terminal block is a buss bar, i modify, 24vdc is on the leff, 0vdc is on the right,,24v coming from power supply an distribute for other uses,, and yes 24v relay board got the power, and i connect it to com terminal,,
- Tue Jun 09, 2020 7:23 am
- Forum: Centroid Acorn CNC Controller
- Topic: Chinese hsd spindle
- Replies: 89
- Views: 34040
Re: Chinese hsd spindle
M3 is trigger output 3, spin foward, m4 is trigger output 5 spind reversed, is that what u means? So what happens to output 4,,martyscncgarage wrote: ↑Tue Jun 09, 2020 12:41 am The Input/Output screen shot shows that M3 should trigger output 3 and that M4 should trigger output 6
- Tue Jun 09, 2020 12:01 am
- Forum: Centroid Acorn CNC Controller
- Topic: Chinese hsd spindle
- Replies: 89
- Views: 34040
Re: Chinese hsd spindle
dear marty,, here the SS that u ask.. in this shoot i have cganged oc 4 to oc3
thanks
thanks
- Mon Jun 08, 2020 11:44 am
- Forum: Centroid Acorn CNC Controller
- Topic: Chinese hsd spindle
- Replies: 89
- Views: 34040
Re: Chinese hsd spindle
Yes marty,, i do the above test already,, m3s1000, and relay is not swicth on, is turn on when put m4 command is typed,, and then m5 is turn the relay off, but when i swicth oc4 to oc3 for spindle foward in the wizard, and is function after test with mdi, m3s1000 oc3 relay is on,,m5, ciyle start is ...
- Mon Jun 08, 2020 2:53 am
- Forum: Centroid Acorn CNC Controller
- Topic: Chinese hsd spindle
- Replies: 89
- Views: 34040
Re: Chinese hsd spindle
Here the picture, 24v is from power supply to com,, and oc3-oc8, i test by manual swicth spindle, reversed is ok oc5, got the light on relay module, and relay is respone,, but not working on oc4,, i change oc4 to oc3, and its work,
- Mon Jun 08, 2020 2:46 am
- Forum: Centroid Acorn CNC Controller
- Topic: Chinese hsd spindle
- Replies: 89
- Views: 34040
Re: Chinese hsd spindle
sorry, here myreport. picture is on the way.. i have use my phone to post it,,is easy that way