If the power supply LED is blinking, then you have a short in the 24vdc system. Your system will not runThe green LED on the Meanwell (power source) constantly blinks
Search found 2164 matches
- Sat Dec 02, 2023 10:02 am
- Forum: Centroid Acorn CNC Controller
- Topic: E-stop config for router
- Replies: 17
- Views: 11910
Re: E-stop config for router
- Fri Dec 01, 2023 3:28 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Gantry squaring - purely manual or CNC12-assisted?
- Replies: 13
- Views: 1615
Re: Gantry squaring - purely manual or CNC12-assisted?
Stepper motors and by extension step & direction DC servos may, in fact will, "jump" into a nearby magnetic detent on startup. Sometimes clockwise, sometimes counterclockwise. Sometimes a few encoder counts, sometimes more. I don't even know if stopping the motor at exactly the same sh...
- Thu Nov 23, 2023 10:58 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Hardware-paired Clearpath gantry servos falls out of step - resolved
- Replies: 19
- Views: 2851
Re: Hardware-paired Clearpath gantry servos fell out of step
This can also be caused by an incomplete or improper auto tune. Especially on dual motor axes
- Thu Nov 23, 2023 10:27 am
- Forum: Centroid Acorn CNC Controller
- Topic: Can Clearpath SDSK & Hybrid Steppers be connected to C86ACCP ?
- Replies: 9
- Views: 1756
Re: Can Clearpath SDSK & Hybrid Steppers be connected to C86ACCP ?
#1: The C86ACCP is not compatible with the AcornSIX
#2: Both your ClearPaths and steppers will connect directly to the AcornSIX via flying leads into the terminal blocks
#3: Most stepper alarms will work with AcornSIX
#4: Are you sure that those <200ozin steppers are suitable for your mill?
#2: Both your ClearPaths and steppers will connect directly to the AcornSIX via flying leads into the terminal blocks
#3: Most stepper alarms will work with AcornSIX
#4: Are you sure that those <200ozin steppers are suitable for your mill?
- Mon Nov 13, 2023 6:59 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Shopsabre 408 with centroid acorn controls
- Replies: 16
- Views: 3203
Re: Shopsabre 408 with centroid acorn controls
Post a link or a PDF of the manual to the servo drives on the machine. They have used a few different ones over the years
- Wed Nov 08, 2023 5:04 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Touch screen latency, or CNC12? <not cnc12>
- Replies: 36
- Views: 2592
- Sun Oct 15, 2023 6:52 pm
- Forum: Centroid Acorn CNC Controller
- Topic: PSA for those building a system with two IPC-5s
- Replies: 2
- Views: 922
Re: PSA for those building a system with two IPC-5s
On my systems I use one 10A D curve breaker for each power supply. You need to upsize breakers for inductive loads due to inrush current
- Sun Oct 15, 2023 6:49 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Probe Protection
- Replies: 5
- Views: 1258
Re: Probe Protection
Reverse the logic of the probe detect input
- Mon Oct 02, 2023 11:55 pm
- Forum: Centroid Acorn CNC Controller
- Topic: 5/24v Signal Stepper Drivers
- Replies: 4
- Views: 990
Re: 5/24v Signal Stepper Drivers
Yes, correct. DB25 header at 5v
- Mon Oct 02, 2023 8:20 pm
- Forum: Centroid Acorn CNC Controller
- Topic: 5/24v Signal Stepper Drivers
- Replies: 4
- Views: 990
Re: 5/24v Signal Stepper Drivers
You haven't provided the model number for the drives, but virtually all stepper drives should be connected as 5v to the DB25 header