Search found 147 matches
- Wed Feb 08, 2023 12:55 am
- Forum: Centroid Acorn CNC Controller
- Topic: Surface probe that generates height deltas
- Replies: 17
- Views: 2240
Re: Surface probe that generates height deltas
I am not compensating for the machine itself however when I V-carve I can get .5mm discrepancies in locations of material that isn't flat or has areas that are hard to notice by eye they are not flat. I guess I will have to create the tool as no one else has this problem. Maybe not too many out the...
- Sun Feb 05, 2023 4:57 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Software enhancements request
- Replies: 77
- Views: 38029
Re: Software enhancements request
It would be nice to add the ability to run a job from the graphing screen rather than reverting back to the home screen to press 'run'
- Thu Nov 17, 2022 10:57 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Random faults will a C86ACCP help?
- Replies: 9
- Views: 1188
Re: Random faults will a C86ACCP help?
Do you have the resistors installed per the latest Acorn/SDSK documentation for Step/direction/Enable?
- Thu Jul 21, 2022 11:54 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Dust Collector
- Replies: 7
- Views: 1102
Re: Dust Collector
You would need two relays from the acorn, one for momentary contact for turning the DC on, and one for momentary contact for turning the DC off. If you look at Oneida's wireless remote line diagram you may be able to parallel with the remote. Another way to do it would be to use the contactor wire t...
- Sat Jun 04, 2022 2:53 pm
- Forum: Centroid Acorn CNC Controller
- Topic: C86ACCP out of stock, should I skip it?
- Replies: 10
- Views: 2411
Re: C86ACCP out of stock, should I skip it?
Do yourself a big favor and skip the C86 board, it causes many people nothing but headaches. It's also just another failure point in the system that's simply not needed. You can buy the 4 channel relay board for the HFLB circuit on Amazon for about $7 and have it tomorrow I'm sure. :mrgreen: Make s...
- Wed May 11, 2022 11:24 pm
- Forum: Centroid Acorn CNC Controller
- Topic: VCP selectable Options for only one active output
- Replies: 2
- Views: 667
VCP selectable Options for only one active output
I am thinking of using a Raspberry Pi zeroW to text the machine operator's phone when there is an error/fault or G-Code file is completed. This is not intended to be a thread discussing leaving the machine unattended or unsafe practices in the shop. This is intended to discuss an additional method t...
- Fri Apr 01, 2022 3:30 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Acorn, Clearpath,C86ACCP and contactor
- Replies: 12
- Views: 2508
Re: Acorn, Clearpath,C86ACCP and contactor
The C86ACCP is not well documented by the seller. My experience with it was beyond a terrible experience. IMO it is a project in process. When the individual for support comments to the effect that 'most people don't understand how it works so we don't publish a manual for everything that it will do...
- Wed Mar 30, 2022 10:46 pm
- Forum: Centroid Acorn CNC Controller
- Topic: New Build: Frame convert into a working machine
- Replies: 103
- Views: 16853
Re: New Build: Frame convert into a working machine
I used one of these https://www.adafruit.com/product/1609 breadboards to mount the resistors and run one +24VDC source, placed a https://www.adafruit.com/product/2671 header on it and used https://www.adafruit.com/product/826 extension wires from the header to the drive cable ferrule on the terminal...
- Wed Mar 30, 2022 1:24 pm
- Forum: Centroid Acorn CNC Controller
- Topic: New Build: Frame convert into a working machine
- Replies: 103
- Views: 16853
Re: New Build: Frame convert into a working machine
Yup, there are two choices, simple direct wire or a complicated, additional board to confuse you that's simply not needed. Seems like an obvious choice to me but I'm a simple caveman and your C86 board confuses me. :mrgreen: And the relay board for the HLFB signal that is recommended by Centroid is...
- Tue Mar 29, 2022 6:42 pm
- Forum: Centroid Acorn CNC Controller
- Topic: New Build: Frame convert into a working machine
- Replies: 103
- Views: 16853
Re: New Build: Frame convert into a working machine
You can use 4 ch relay boards for the HLFB to interface to one Acorn Input or individual inputs to the ETHER1616.