Search found 144 matches

by RogDC
Sat Nov 11, 2023 5:40 pm
Forum: Public Beta CNC Software Testing, Discussion and Feedback
Topic: CNC12 v5.07 rev14 now available for download.
Replies: 18
Views: 7001

Re: CNC12 v5.07 rev14 now available for download.

During re-calibrating my machine auto-square from prior issue, I discovered the following issue. I use G30 for my tool touch off plate to measure tool Z-Offset. The G-30 Z value is being over-written at what I presume machine homing or Z part zero to the Y value. I have been able to repeat the condi...
by RogDC
Sat Nov 11, 2023 2:27 pm
Forum: Public Beta CNC Software Testing, Discussion and Feedback
Topic: CNC12 v5.07 rev14 now available for download.
Replies: 18
Views: 7001

Re: CNC12 v5.07 rev14 now available for download.

Installed 64 bit 5.07r14 last night, went to test cut today and ran into a slight problem Router with paired 2 & 4 axis autosquare, had to re-home and ran into an error with Y-travel exceeded, homing operation was interrupted, unable to move off of limit switch with MPG or VCP, exited CNC12, pow...
by RogDC
Fri Nov 10, 2023 4:55 pm
Forum: Centroid Acorn CNC Controller
Topic: Add on laser, need opinions
Replies: 2
Views: 376

Re: Add on laser, need opinions

I ordered an Ox Laser module 5W from Amazon and made a mount on my dust shoe for easy mounting when I use it. Everything is packaged on the laser module (no additional boards/controls) so I just have a 4 pin molex near the spindle that I plug into the unit's pigtail, then use the mean-well power sup...
by RogDC
Thu Nov 09, 2023 4:32 pm
Forum: Centroid Acorn CNC Controller
Topic: Router-machined countersink holes?
Replies: 3
Views: 291

Re: Router-machined countersink holes?

Check out Drillman1 on ebay, they have various countersink endmills. Not sure what CAD/CAM program you are using, with Vectric V-Carve you could use one of his inexpensive 1/8" endmill or ball nose endmill for tapered countersink.
by RogDC
Wed Nov 08, 2023 11:09 pm
Forum: Public Beta CNC Software Testing, Discussion and Feedback
Topic: Centroid CNC12 v5.07 REV12 BETA is now available.
Replies: 35
Views: 7940

Re: Centroid CNC12 v5.07 REV12 BETA is now available.

Joey, I tested the WMPG more this afternoon. I tried to take a video but wasn't able to hold the phone while holding and operating the MPG. I'll try to explain what I validated today in testing. With Z limit enabled in WMPG settings in Wizard, When you use the jog -/+ buttons on the WMPG, the 100x m...
by RogDC
Wed Nov 08, 2023 12:36 am
Forum: Public Beta CNC Software Testing, Discussion and Feedback
Topic: Centroid CNC12 v5.07 REV12 BETA is now available.
Replies: 35
Views: 7940

Re: Centroid CNC12 v5.07 REV12 BETA is now available.

One other item I noticed on the WMPG jogging is the setting for Z speed limit Zx100=Zx10 does not appear to limit to x10 after homing and prior to Z-zero . The Z movement with the WMPG set on 100x is 100x speed until you touch off the z reference ( Bed or material ), then appears to function correct...
by RogDC
Tue Nov 07, 2023 7:49 pm
Forum: Centroid Acorn CNC Controller
Topic: Touch screen latency, or CNC12? <not cnc12>
Replies: 36
Views: 2593

Re: Touch screen latency, or CNC12?

Or, more likely since this seems to only occur on your machine, there is some process, like a firewall or disk encryption, that is causing the issue. Agree that this could be only my machine. Thing is, this PC was bought brand new specifically for this, so it's a clean install on a clean machine. T...
by RogDC
Thu Nov 02, 2023 3:50 pm
Forum: Public Beta CNC Software Testing, Discussion and Feedback
Topic: Centroid CNC12 v5.07 REV12 BETA is now available.
Replies: 35
Views: 7940

Re: Centroid CNC12 v5.07 REV12 BETA is now available.

Experienced delayed movement with the WMPG-4 last night, no video, but not getting consistent performance. Movement was jerky, and intermittently delayed from WMPG-4 commands.
by RogDC
Wed Nov 01, 2023 10:39 pm
Forum: Public Beta CNC Software Testing, Discussion and Feedback
Topic: Centroid CNC12 v5.07 REV12 BETA is now available.
Replies: 35
Views: 7940

Re: Centroid CNC12 v5.07 REV12 BETA is now available.

I've had an issue with how an MPG responds with the wheel in some of the past beta's (a CWP-4 in my case)... https://centroidcncforum.com/viewtopic.php?p=74658#p74658 ...It seems to be even more pronounce with v5.07r12. I do have a coupe of videos I can upload, but it's not as easy to tell the diff...