Tom T.
Thanks for the informative explanation!
Search found 41 matches
- Fri Feb 19, 2021 9:01 am
- Forum: Centroid Acorn CNC Controller
- Topic: Lost steps newly upgraded machine <clearpath, resistors>
- Replies: 44
- Views: 17628
- Mon Feb 15, 2021 4:10 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Lost steps newly upgraded machine <clearpath, resistors>
- Replies: 44
- Views: 17628
Re: Lost steps newly upgraded machine <clearpath, resistors>
22 gauge wire should only be .516 ohms at 32ft
- Mon Feb 15, 2021 3:48 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Lost steps newly upgraded machine <clearpath, resistors>
- Replies: 44
- Views: 17628
Re: Lost steps newly upgraded machine <clearpath, resistors>
Mike, Marty, Thanks for the help, I am sure this will help many in the future also, I have the same diagram Mike has with the 1K ohm resistors, notice how the diagram says step and direction and after just calling, Abe said to use them on both and step and direction and mentioned that they were work...
- Fri Feb 12, 2021 7:34 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Clearpath Enable Connections to Acorn
- Replies: 18
- Views: 6027
Re: Clearpath Enable Connections to Acorn
Mike
You nailed it, I had the jumpers on high setting thinking the HLFB was a 5v signal, changed the jumpers to Low and the relays closing as they should,
Thanks for your help, much appreciated.
You nailed it, I had the jumpers on high setting thinking the HLFB was a 5v signal, changed the jumpers to Low and the relays closing as they should,
Thanks for your help, much appreciated.
- Fri Feb 12, 2021 7:29 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Lost steps newly upgraded machine <clearpath, resistors>
- Replies: 44
- Views: 17628
Re: Lost steps newly upgraded machine
Marty, thanks for your reply I watch all your vids on youtube. Cable length 32 ft. No resistors, I skimmed over that page 47-48 in the teknic literature but the Acorn board diagram doesnt show them, thats what was confusing. Update; I called into Teknic today and spoke with Abe, he was very helpful ...
- Thu Feb 11, 2021 5:28 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Lost steps newly upgraded machine <clearpath, resistors>
- Replies: 44
- Views: 17628
Lost steps newly upgraded machine <clearpath, resistors>
Latest version of CNC12 router Clearpath SDSK motors 3kw spindle Shielded vfd wire with ferrites, vfd mounted in a separate box, wire on a boom far away from signal wire. report_0C1C570447DB-0403203101_2021-02-11_12-26-18.zip Measurements and cut quality seem to be very good, out of the dozen files ...
- Thu Feb 11, 2021 2:52 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Clearpath Enable Connections to Acorn
- Replies: 18
- Views: 6027
Re: Clearpath Enable Connections to Acorn
Mike and Gary, Thanks for the information, and I dont mean to hijack this thread I didnt start. But reading thru it made me check how I'd wired mine and I tried crashing the Z into a block of wood to fault it and it never did fault this relay board, (wired to NC side to IN5 sees common) https://www....
- Wed Feb 10, 2021 6:22 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Clearpath Enable Connections to Acorn
- Replies: 18
- Views: 6027
Re: Clearpath Enable Connections to Acorn
Mike Richards,
Not sure if you were replying to my post or not, I was talking about the HLFB circuit from a SDSK clearpath motors. As drawn in the diagram it did not work. The alarm circuit opens that common IN5 and causes a fault. My proximity sensors are on IN1 AND IN2.
Not sure if you were replying to my post or not, I was talking about the HLFB circuit from a SDSK clearpath motors. As drawn in the diagram it did not work. The alarm circuit opens that common IN5 and causes a fault. My proximity sensors are on IN1 AND IN2.
- Wed Feb 10, 2021 5:56 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Setting Z Height at tool change
- Replies: 7
- Views: 2486
Re: Setting Z Height at tool change
Nigelo, So the built in macro calls on the tool library, now I am beginning to understand it. I'm on a router. I do not have fixed tool holders and I'm unable to measure a tool Z height when one file has more than one tool. A stupid question. How do I measure a tool immediately when the M6 command b...
- Tue Feb 09, 2021 7:27 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Clearpath Enable Connections to Acorn
- Replies: 18
- Views: 6027
Re: Clearpath Enable Connections to Acorn
I wired mine as per this wiring diagram and the HLFB +GRN wont close the relays the way it is drawn, if IN2 closes that relays it goes nowhere. I had to wire mine on the normally closed side to make it work. Did I read the diagram wrong? wrong relay board?