Search found 3097 matches
- Sun Mar 24, 2024 6:04 pm
- Forum: Centroid Acorn CNC Controller
- Topic: What's the minimum I need for a small lathe?
- Replies: 17
- Views: 489
Re: What's the minimum I need for a small lathe?
Not relevant. The only thing Centroid cares about is the spindle.
- Sun Mar 24, 2024 7:22 am
- Forum: Centroid Acorn CNC Controller
- Topic: Program eratic after a tool change Lathe <resolved. CSS was too high>
- Replies: 26
- Views: 867
Re: Program eratic after a tool change Lathe
Marc already explained this. At 1000 meters/min, you are already at your max rpm at the stock diameter. There is no way for the spindle to increase any more when the part gets smaller.PhilipTrueman wrote: ↑Sun Mar 24, 2024 5:40 am One thing that doesn't happen is that the spindle doesn't change speed as the tool goes to a smaller diameter.
- Sat Mar 23, 2024 9:56 pm
- Forum: Centroid Acorn CNC Controller
- Topic: No motor movement
- Replies: 7
- Views: 331
Re: No motor movement
The 2K series resistor just drops the voltage. Save yourself trouble down the road and connect them according to the manufacturer of the CNC control who says to use the DB25 connector.
- Fri Mar 22, 2024 1:55 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Program eratic after a tool change Lathe <resolved. CSS was too high>
- Replies: 26
- Views: 867
Re: Program eratic after a tool change Lathe
The fact that it does not return to zero, implies that you are overdriving your motors and loosing steps. What are your programmed feed rates for the grooving tool? Common mistake is to program a valid range in feed per minute, but have the feed set for feed per rev. That will almost always cause mi...
- Fri Mar 22, 2024 1:53 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Rigid Tapping Setup
- Replies: 36
- Views: 1261
Re: Rigid Tapping Setup
Until you know there is noise on the analog input from the Acorn, then it could be internal noise in the driver converting the analog signal to digital. When running the driver in test or jog mode, the up/down buttons generate digital signals, not analog ones that route through the analog to digital...
- Fri Mar 22, 2024 7:35 am
- Forum: Centroid Acorn CNC Controller
- Topic: Rigid Tapping Setup
- Replies: 36
- Views: 1261
Re: Rigid Tapping Setup
Do you even know if it's interference? Have you looked at the signal when the inverter is running? Is interference visible?
- Fri Mar 22, 2024 7:12 am
- Forum: Centroid Acorn CNC Controller
- Topic: Program eratic after a tool change Lathe <resolved. CSS was too high>
- Replies: 26
- Views: 867
Re: Program eratic after a tool change Lathe
Immediately after the weird moves with the parting blade, what happens if you restart the program from the beginning? Does the first tool run correctly?
- Thu Mar 21, 2024 4:52 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Rigid Tapping Setup
- Replies: 36
- Views: 1261
Re: Rigid Tapping Setup
It may be a problem in the analog to digital conversion within the servo drive. Unless there are some filtering parameters in the drive for the analog input, then you may not be able to to fix it without changing the servo drive.
- Wed Mar 20, 2024 7:08 am
- Forum: Machining Strategies. Work Holding, Tool Path, Cutters, Feeds/Speeds etc.
- Topic: Z axis does what it wants...
- Replies: 3
- Views: 266
Re: Z axis does what it wants...
You might want to check on the Eding-CNC forum. This forum is for Centroid CNC products.
- Tue Mar 19, 2024 3:50 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Ethernet or Crossover Ethernet?
- Replies: 3
- Views: 197
Re: Ethernet or Crossover Ethernet?
Of note, the Acorn kit comes with all of the necessary cables, including a shielded Ethernet cable.