Search found 31 matches
- Tue Feb 22, 2022 11:14 am
- Forum: Centroid Acorn CNC Controller
- Topic: New STEPPERONLINE Integrated Servo motor
- Replies: 44
- Views: 8569
Re: New STEPPERONLINE Integrated Servo motor
No worries. I fixed the issue by checking and turning off the firewall again.
- Tue Feb 22, 2022 10:34 am
- Forum: Centroid Acorn CNC Controller
- Topic: New STEPPERONLINE Integrated Servo motor
- Replies: 44
- Views: 8569
Re: New STEPPERONLINE Integrated Servo motor
Gents, I need help again. After meticulous planning I reassembled the control box with properly wired everything. See the picture of the setup. I followed Marty's procedure on checking the power first and then connected it to the acorn board. I was able to launch CNC12 and communicate with the board...
- Wed Feb 02, 2022 12:55 pm
- Forum: Centroid Acorn CNC Controller
- Topic: New STEPPERONLINE Integrated Servo motor
- Replies: 44
- Views: 8569
Re: New STEPPERONLINE Integrated Servo motor
Thank you, Shawn. It clears the picture. I had a single NC switch on my e-stop, so I ordered another one with double NC. I will use one to run input 8 with 24v and another one at 110v for Relay 1 with assigned "NoFaultOut" that energizes contactor coil for motor power. It was important for...
- Tue Feb 01, 2022 12:59 pm
- Forum: Centroid Acorn CNC Controller
- Topic: New STEPPERONLINE Integrated Servo motor
- Replies: 44
- Views: 8569
Re: New STEPPERONLINE Integrated Servo motor
Gents, here is another confusion. I accidently bought contactor with 110v coil. I was planning to use the feed from the breaker to energize the coil and connect the motor power, but I am not sure that I can mix 24v circuit that goes into Input 8 and 110v for the contactor coil in the same e-stop but...
- Mon Jan 24, 2022 8:07 pm
- Forum: Centroid Acorn CNC Controller
- Topic: New STEPPERONLINE Integrated Servo motor
- Replies: 44
- Views: 8569
Re: New STEPPERONLINE Integrated Servo motor
Gents, just got my new stepper motors and benchtest them. Looks like everything works fine. Using Driver template in the wizard resulted in increased frequency of the Acorn from 100k to 200k and to 4000 steps per rev, which I adjusted on the motor drivers. I am ready to assemble them, but here are a...
- Sun Jan 16, 2022 9:45 am
- Forum: Centroid Acorn CNC Controller
- Topic: New STEPPERONLINE Integrated Servo motor
- Replies: 44
- Views: 8569
Re: New STEPPERONLINE Integrated Servo motor
Clarification question: based on lead screw limitation and for the closed-loop motor the top recommended working rpm is 800 rpm, that translates into 250 ipm, but what would be the suggested rapid movement without load (G0)? What numbers should I use in Acorn Wizard for max ipm on the axes? Also, do...
- Sat Jan 15, 2022 2:44 pm
- Forum: Centroid Acorn CNC Controller
- Topic: New STEPPERONLINE Integrated Servo motor
- Replies: 44
- Views: 8569
Re: New STEPPERONLINE Integrated Servo motor
Thank you, gents. You shared very valuable information for me that really explained the connection between motors and mechanical parts of the machine and gave me the basis to fine-tune it to its maximum ability. I believe the consensus is that I need closed-loop steppers as servos will not be able t...
- Fri Jan 14, 2022 10:45 pm
- Forum: Centroid Acorn CNC Controller
- Topic: New STEPPERONLINE Integrated Servo motor
- Replies: 44
- Views: 8569
Re: New STEPPERONLINE Integrated Servo motor
Thank you, Scott. Your work is amazing! Really piece of art. Good suggestion about feed rate for Z axes. I will try this trick. What acceleration you suggest instead of 0.5? This number is really cryptic to me, I cannot make any real sense out of it. I will study your thread and will most like come ...
- Fri Jan 14, 2022 7:59 pm
- Forum: Centroid Acorn CNC Controller
- Topic: New STEPPERONLINE Integrated Servo motor
- Replies: 44
- Views: 8569
Re: New STEPPERONLINE Integrated Servo motor
It is 8 mm move per revolution confirmed.
- Fri Jan 14, 2022 7:08 pm
- Forum: Centroid Acorn CNC Controller
- Topic: New STEPPERONLINE Integrated Servo motor
- Replies: 44
- Views: 8569
Re: New STEPPERONLINE Integrated Servo motor
Sorry, it took some time to write the file. Here is the better one.