Search found 43 matches
- Sat Feb 26, 2022 8:15 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Update controls on Hendricks 2008 CNC
- Replies: 61
- Views: 10954
Re: Update controls on Hendricks 2008 CNC
Sent Cncsnw an email on this. Got the machine running and actually cut a product part, foam core for fiberglass composite. Also cut a mold shape out of mdf. The mdf part is basically a circle and has 3 degrees of taper. On the mdf part it is way out of round. 10-5/16” across one axis and 10-9/16” ac...
- Sun Feb 20, 2022 7:06 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Update controls on Hendricks 2008 CNC
- Replies: 61
- Views: 10954
Re: Update controls on Hendricks 2008 CNC
I will check. Went old schuand printed a manual including installation manual and relabel Tech bulletins.
- Sun Feb 20, 2022 4:55 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Update controls on Hendricks 2008 CNC
- Replies: 61
- Views: 10954
Re: Update controls on Hendricks 2008 CNC
Ran our first test part today. I model in rhino so I had a part that needs to be rerun and we tried it on a piece of scrap. My son and I build fiberglass parts which utilize foam cores. We also use melamine to fabricate temporary molds. So this test piece is a scrape melamine sheet and the shape wil...
- Wed Feb 16, 2022 3:48 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Update controls on Hendricks 2008 CNC
- Replies: 61
- Views: 10954
Re: Update controls on Hendricks 2008 CNC
Thanks cncsnw, we adjusted the turns and got it close. Need to get a dial indicator and finalize it.
- Tue Feb 15, 2022 11:21 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Update controls on Hendricks 2008 CNC
- Replies: 61
- Views: 10954
Re: Update controls on Hendricks 2008 CNC
After getting cncsnw reply I checked the 24 vdc power to board and all was good. In parallel I had read that the yaskawa drives should have a 5 second delay between logic power and then drive power to allow alarm to clear. So we powered up with estop engaged. Then after 5 seconds reset. Miraculously...
- Sun Feb 13, 2022 12:58 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Update controls on Hendricks 2008 CNC
- Replies: 61
- Views: 10954
Re: Update controls on Hendricks 2008 CNC
Verified we do have 22.4vdc on oak.
- Sun Feb 13, 2022 8:35 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Update controls on Hendricks 2008 CNC
- Replies: 61
- Views: 10954
Re: Update controls on Hendricks 2008 CNC
I did wire H2 with 24 vac but I have not metered it to be sure it is working. Thinking about it I could not get the spindle to turn and I checked it and had no volt at varies speed calls. Figured it was because we were not complete. That said the bench test worked well? I will check it out this morn...
- Sat Feb 12, 2022 5:35 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Update controls on Hendricks 2008 CNC
- Replies: 61
- Views: 10954
Re: Update controls on Hendricks 2008 CNC
Made changes to drive program. That got rid of code 810. Drives show 66. We don’t have the “code book” so at a loss for what that means. We did start getting encoder feedback what felt like randomly but I suspect my son is not saving or existing correctly. We are not able to home or move the machine...
- Sat Feb 12, 2022 1:36 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Update controls on Hendricks 2008 CNC
- Replies: 61
- Views: 10954
Re: Update controls on Hendricks 2008 CNC
Ok. We will see if we can get it corrected. Sent you a message as well. Thank you
- Sat Feb 12, 2022 10:28 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Update controls on Hendricks 2008 CNC
- Replies: 61
- Views: 10954
Re: Update controls on Hendricks 2008 CNC
So as we start up to try and set up to home the machine this is the fault. Drive fault (9045 ). We can’t get to MDI To clear.
On the drive itself it is flashing 810 and they only clear thru the yaskawa. We unplugged the two wire pig tails mentioned above.
On the drive itself it is flashing 810 and they only clear thru the yaskawa. We unplugged the two wire pig tails mentioned above.