Thank you for the explanation.
Is there anything you do not know about Centroid ?
Uwe
Search found 2106 matches
- Wed May 22, 2024 4:07 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Feature Request - SSV
- Replies: 21
- Views: 1886
- Wed May 22, 2024 3:47 pm
- Forum: Centroid Acorn CNC Controller
- Topic: CNC12 and RS-485...
- Replies: 8
- Views: 56
Re: CNC12 and RS-485...
AFAIK, the spindle on/off is currently controlled by a relay in the SB control box. It looks like the docs show rotation direction is controlled with relays...which is sub-optimal. I will absolutely investigate with those two M codes and report back. Thanks for that. Unfortunately, it may be a coup...
- Wed May 22, 2024 1:55 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Rough Motion on Circular Toolpaths
- Replies: 31
- Views: 497
Re: Rough Motion on Circular Toolpaths
If the motor is only vibrating at very low speed, gearing would avoid this low speed on the motor, so it will run smooth while cutting with the same feedrate it is now vibrating.Salted_Pork wrote: ↑Wed May 22, 2024 1:50 pm
Would gearing the motors to spin faster be a good solution?
Cheers,
Mitchell
Uwe
- Wed May 22, 2024 12:58 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Feature Request - SSV
- Replies: 21
- Views: 1886
Re: Feature Request - SSV
It works with threading also
But why is G10 on the lathe different than on the mill ?
Mill : G10 P980 R1
Lathe : G10 P1980 R1
Uwe
But why is G10 on the lathe different than on the mill ?
Mill : G10 P980 R1
Lathe : G10 P1980 R1
Uwe
- Wed May 22, 2024 11:57 am
- Forum: Centroid Acorn CNC Controller
- Topic: Acorn single axis
- Replies: 6
- Views: 131
Re: Acorn single axis
Even single axis Acorn is full CNC. If the axis is konfigured ok, you can set Z 0 for the lowest point and use MDI with G1 Z0.5 F200 to drive exactly 0.5 above the lowest point. Since Acorn is with one encoder port ist is possible to connect a scale. I am only not sure if ultimate is required for cl...
- Wed May 22, 2024 9:52 am
- Forum: Centroid Acorn CNC Controller
- Topic: AC Servo suggestions?
- Replies: 13
- Views: 593
Re: AC Servo suggestions?
Yes they are cheaper on Ali, but not with next day delivery on purchase or in case of guarantee...
Uwe
Uwe
- Wed May 22, 2024 8:14 am
- Forum: Public Beta CNC Software Testing, Discussion and Feedback
- Topic: CNC12 Router Restructure Beta Software thread.
- Replies: 4
- Views: 239
Re: CNC12 Router Restructure Beta Software thread.
Nice, I hope this will be implemented in the mill version also
Uwe
Uwe
- Wed May 22, 2024 5:25 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Feature Request - SSV
- Replies: 21
- Views: 1886
Re: Feature Request - SSV
Test on my lathe
D14 1.4404 steel ap0.5mm F0.25mm S2500 min-1, turned down to 12mm, Z0 140mm in front of the chuck
SSV with 1.5s +-200 rpm
I would say a significant improvement compared to turning without SSV.
Uwe
D14 1.4404 steel ap0.5mm F0.25mm S2500 min-1, turned down to 12mm, Z0 140mm in front of the chuck
SSV with 1.5s +-200 rpm
I would say a significant improvement compared to turning without SSV.
Uwe
- Wed May 22, 2024 3:16 am
- Forum: Centroid Acorn CNC Controller
- Topic: AC Servo suggestions?
- Replies: 13
- Views: 593
- Wed May 22, 2024 1:09 am
- Forum: Centroid Acorn CNC Controller
- Topic: AC Servo suggestions?
- Replies: 13
- Views: 593
Re: AC Servo suggestions?
I am using JMC AC Servos for axis and spindle, they work very well. Uwe Where is your preferred place to buy these? Do they have a decent programming software and documentation ? How is the auto tuning? Currently have some ethercat delta B3A servos. I like that they have STO and allow me to use aco...