Download TeamViewer
https://www.teamviewer.com
Search found 512 matches
- Wed Apr 24, 2024 1:13 pm
- Forum: Acorn CNC Plasma
- Topic: Centroid v 4, extends and hits the material.
- Replies: 6
- Views: 201
- Wed Apr 24, 2024 11:49 am
- Forum: Acorn CNC Plasma
- Topic: Speed around corners
- Replies: 2
- Views: 37
Re: Speed around corners
What Kind of Drives are on X,Y and Z? Is this a direct rack and pinion table?
Pictures of each axis and the drives would help
Pictures of each axis and the drives would help
- Tue Apr 23, 2024 9:35 pm
- Forum: Acorn CNC Plasma
- Topic: Speed around corners
- Replies: 2
- Views: 37
Re: Speed around corners
Can you post some of the G-code jobs from the example Pictures. Does the same thing happen without smoothing? Try setting parameter 223 to 300 Path to the Parameters list from the home screen is F1 Setup>F3 Config>F3 Parameters This will Lower the Vector rate with smoothing and should help for smoot...
- Mon Apr 22, 2024 6:10 pm
- Forum: Public Beta CNC Software Testing, Discussion and Feedback
- Topic: V5.1 Lathe distance to go isn't working
- Replies: 3
- Views: 109
Re: V5.1 Lathe distance to go isn't working
I was not able to replicate the issue with your report.
Usually, the X moves in the G-code I tested with was very short and the distance to go was shown briefly since the X move was very short and quickly executed.
Usually, the X moves in the G-code I tested with was very short and the distance to go was shown briefly since the X move was very short and quickly executed.
- Mon Apr 22, 2024 6:04 pm
- Forum: Public Beta CNC Software Testing, Discussion and Feedback
- Topic: Centroid V5.10 tool number
- Replies: 4
- Views: 137
Re: Centroid V5.10 tool number
This is a result of pressing write setting with the Custom ATC macro set to yes. Doing this is making an assumption that the user will set these parameters manually. What most people do is have the slider set to no press write setting to cnc control at least once which sets all ATC parameters proper...
- Mon Apr 22, 2024 12:54 pm
- Forum: Acorn CNC Plasma
- Topic: centroid with sheetcam.
- Replies: 2
- Views: 69
Re: centroid with sheetcam.
The M61 Macro can be Customized to Operate differently. Can you Post some example Gcode of a Wiggle Peirce? I'm assuming you would be looking for something like. M61 is called Touch off cycle and the Z retracts to the Pierce Height. The torch is fired and X Y motion starts for the Wiggle pierce. Aft...
- Sun Apr 21, 2024 1:16 pm
- Forum: Acorn CNC Plasma
- Topic: drivers ok with centroid? and circuit board standoffs
- Replies: 2
- Views: 110
Re: drivers ok with centroid? and circuit board standoffs
The Wiring looks the same. Schematic S15034 will work. You want continuity from the stand offs all the way thru to the cabinet. All ground and Shields should be Attached at a single point bar or terminal strip Not 100% sure on the stand off length but I think for the Acorn at least a 1/4 inch length...
- Fri Apr 19, 2024 6:43 pm
- Forum: Acorn CNC Plasma
- Topic: Laser Alignment
- Replies: 9
- Views: 248
Re: Laser Alignment
I was not able to replicate any issues or the Laser offset in the Wizard not working.
Id be happy to try a TeamViewer session with you to try and pinpoint this issue.
Id be happy to try a TeamViewer session with you to try and pinpoint this issue.
- Fri Apr 19, 2024 5:31 pm
- Forum: Acorn CNC Plasma
- Topic: Issues with Torch Calibration
- Replies: 29
- Views: 952
Re: Issues with Torch Calibration
Wow, Good on ya for finding the Issue. That sounded frustrating.
Thanks for sharing the Conclusion and Lessons learned
Thanks for sharing the Conclusion and Lessons learned
- Thu Apr 18, 2024 7:07 pm
- Forum: Acorn CNC Plasma
- Topic: Laser Alignment
- Replies: 9
- Views: 248
Re: Laser Alignment
Joey, Hi ... That's exactly what I'm doing .. test fire, then click " Laser Set XY " follow the on screen macro instruction to set the offset After this is done, I want to move to a piece which requires cutting, I need to select start point on that piece ... that's where I'm saying its lo...