Search found 534 matches
- Sat Aug 31, 2024 2:24 pm
- Forum: Acorn CNC Plasma
- Topic: Hypertherm 45 xp Voltage Divider
- Replies: 4
- Views: 816
Re: Hypertherm 45 xp Voltage Divider
cheers joey, and thanks for reply. i forgot to answere, when im up and running i will read voltage output from cpc output and see what it reads, hang on, i cant really unless its cutt :geek: ing at full amps to check voltage level? cheers I'm not so sure Amperage has much to do with the divided vol...
This post has been liked 0 time(s).
- Sat Aug 31, 2024 2:08 pm
- Forum: Acorn CNC Plasma
- Topic: Centroid CNC Plasma Manual error?
- Replies: 1
- Views: 24
Re: Centroid CNC Plasma Manual error?
This was an error in the manual that went under the radar. The highlighted blue sentence is the correct one. Screenshot_20240831-141500.png The highlight red sentence should read. 1-2.5 revolutions of the motor per 1 inch of travel 2 inches of travel per 1 rev of the motor is an overall turns ratio ...
This post has been liked 0 time(s).
- Wed Aug 21, 2024 1:50 pm
- Forum: Acorn CNC Plasma
- Topic: Post Processor Sheet Cam/Fusion 360
- Replies: 10
- Views: 8243
Re: Post Processor Sheet Cam/Fusion 360
Hi Joey Many thanks for the reply. I'm not running Acorn Plasma I'm running the machine with Acorn Mill. The Acorn was purchased some years ago before the Plasma software was released. It's just the feedrate syntax error I cannot get my head around. Does the Acorn Plasma handle Sheetcam differently...
This post has been liked 0 time(s).
- Tue Aug 20, 2024 11:37 am
- Forum: Acorn CNC Plasma
- Topic: Post Processor Sheet Cam/Fusion 360
- Replies: 10
- Views: 8243
Re: Post Processor Sheet Cam/Fusion 360
Hi New to the forum and I'm trying to get Sheetcam to work with my Acorn control. I have downloaded the post processor but when I try to run the code I get a syntax error. I am not using the Acorn THC but I am using another THC, I have edited the post to accept my arc ok signal but that's all. I ha...
This post has been liked 0 time(s).
- Tue Aug 20, 2024 11:21 am
- Forum: Acorn CNC Plasma
- Topic: Hypertherm 45 xp Voltage Divider
- Replies: 4
- Views: 816
Re: Hypertherm 45 xp Voltage Divider
I asked the same a while back and I was told on here that its ok and not to worry, i still havent finished my cabinet so not running to tell you first hand. i think its a fair bit more being another 6volts and thought it would cause damage but have been told by cncKeith ALL OK. can cnckeith confirm...
This post has been liked 0 time(s).
- Thu Aug 15, 2024 10:37 am
- Forum: Acorn CNC Plasma
- Topic: intercon quit working
- Replies: 13
- Views: 2138
Re: intercon quit working
I'm thinking Intercon is locked up. Can you find Intercon in the Task manager? Probably need to force close it.rfranklin87 wrote: ↑Thu Aug 15, 2024 9:42 am Intercon plasma quit working wrote a program and ran it just fine come back to write another program and it will not open.
This post has been liked 0 time(s).
- Wed Aug 14, 2024 2:58 pm
- Forum: Acorn CNC Plasma
- Topic: Acorn Plasma Questions
- Replies: 3
- Views: 1262
Re: Acorn Plasma Questions
I've been running the Acorn Plasma for almost a year now. Over that time I've complied a list of questions: 1. Is it possible to have gcode load the correct Cut Profile? For example, in sheetcam when I use the 1/4" steel tool for the kerf offset. Could it also call for the 1/4" steel Cut ...
This post has been liked 0 time(s).
- Wed Aug 14, 2024 10:58 am
- Forum: Acorn CNC Plasma
- Topic: Acorn Plasma THC Controller as router
- Replies: 4
- Views: 3109
Re: Acorn Plasma THC Controller as router
Yes, You can switch at any time.
The only change between Plasma and Router is the software folder and license file.
The only change between Plasma and Router is the software folder and license file.
This post has been liked 0 time(s).
- Thu Aug 01, 2024 12:44 pm
- Forum: Acorn CNC Plasma
- Topic: New Build. can't get motion. Koike Monograph w/ Acorn CNC Plasma & Stepperonline
- Replies: 19
- Views: 4798
Re: New Build. can't get motion. Koike Monograph w/ Acorn CNC Plasma & Stepperonline
hmm.... Can you post some more pictures of the Acorn - drive wiring.
When viewing the current cabinet picture it seems the drives are not connected to the Acorn or breakout board?
Id like to be able to trace out every connection from the Acorn to the drives.
When viewing the current cabinet picture it seems the drives are not connected to the Acorn or breakout board?
Id like to be able to trace out every connection from the Acorn to the drives.
This post has been liked 0 time(s).
- Thu Jul 25, 2024 2:16 pm
- Forum: Acorn CNC Plasma
- Topic: issue with plasma intercon V0.91 BETA
- Replies: 10
- Views: 3414
Re: issue with plasma intercon V0.91 BETA
Changes were made to the Forum, Plasma Intercon .icp files are now accepted
This post has been liked 0 time(s).