Speeding the Z up more should also help. 200ipm max rate could be better. Max the Z out and find its limit.
I'll look into THC turning off when in restart. Restart should reset all settings back to how they were set when entering restart mode.
Search found 528 matches
- Mon Jun 03, 2024 1:18 am
- Forum: Acorn CNC Plasma
- Topic: Corrugated Issues
- Replies: 4
- Views: 17
- Mon Jun 03, 2024 1:11 am
- Forum: Acorn CNC Plasma
- Topic: THC problem
- Replies: 4
- Views: 72
Re: THC problem
For reliable THC operation always run a job with Feed Rate over ride set to 100%. I would set set the Cut height slightly higher to give the Z more time to react if possible. Or dial back the Feedrate. Try to cut at the slowest Feedrate and amperage as possible to get the Z more time to react. Tune ...
- Sun Jun 02, 2024 6:47 pm
- Forum: Acorn CNC Plasma
- Topic: Corrugated Issues
- Replies: 4
- Views: 17
Re: Corrugated Issues
What is the X and Y and Z Accel decell settings?
Can you attach a picture of the Wizards Configuration menu please
Try a higher cut height to give the Z axis more time to react.
Do you have a THC plot capture of the Cut in the Video?
If so please attach a snip picture of the plot.
Can you attach a picture of the Wizards Configuration menu please
Try a higher cut height to give the Z axis more time to react.
Do you have a THC plot capture of the Cut in the Video?
If so please attach a snip picture of the plot.
- Sat Jun 01, 2024 2:39 pm
- Forum: Acorn CNC Plasma
- Topic: THC problem
- Replies: 4
- Views: 72
Re: THC problem
Your making progress. The purple is the THC anti dive. This is controlled by the Anti Dive Hysteresis in the THC config. If the voltage rises more than 7 percent of the target voltage then anti dive will kick in. Default settings is 7 percent o believe I would increase the anti dive from the stock 7...
- Mon May 27, 2024 4:32 pm
- Forum: Acorn CNC Plasma
- Topic: Torch calibration program
- Replies: 1
- Views: 143
Re: Torch calibration program
Torch Calibration is in the "Utils" button on the bottom of the VCP.
- Sun May 26, 2024 9:34 am
- Forum: Acorn CNC Plasma
- Topic: Acorn Plasma THC Controller as router
- Replies: 2
- Views: 105
Re: Acorn Plasma THC Controller as router
Yes
When installing CNC12 you will see an option for a Router/ Plasma combination.
The installer will download both Router and Plasma versions with a Desktop swap button for jumping from the plasma to router software.
When installing CNC12 you will see an option for a Router/ Plasma combination.
The installer will download both Router and Plasma versions with a Desktop swap button for jumping from the plasma to router software.
- Wed May 22, 2024 2:46 pm
- Forum: Acorn CNC Plasma
- Topic: SHEET CAM
- Replies: 15
- Views: 4029
Re: SHEET CAM
There is a video link in my Post found here https://centroidcncforum.com/viewtopic. ... eed#p67483
- Thu May 16, 2024 3:24 pm
- Forum: Acorn CNC Plasma
- Topic: Turns/inch motor shaft
- Replies: 5
- Views: 373
Re: Turns/inch motor shaft
Thanks for pointing this out Guys, Pg.3 and 9 of the Plasma Manual has been updated.
You can find the Updated manual here
https://www.centroidcnc.com/centroid_di ... manual.pdf
You can find the Updated manual here
https://www.centroidcnc.com/centroid_di ... manual.pdf
- Tue May 07, 2024 5:37 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Machine parameter for Linear encoder input
- Replies: 11
- Views: 729
Re: Machine parameter for Linear encoder input
The AIKRON Model:AKM1 Has been Tested at Centroid. The Signal Type Needs to be the 5v RS422 https://www.aikrondro.com/product/aikron-akm-series-linear-encoders/ I've attached a snip of the DB9 connector of the Aikron and the Changes needed to match the Centroid DB9 Encoder Port. Aikron Scale Wiring....
- Tue May 07, 2024 4:47 pm
- Forum: Acorn CNC Plasma
- Topic: SheetCam Hypertherm 45XP .tool file (inch)
- Replies: 1
- Views: 207
Re: SheetCam Hypertherm 45XP .tool file (inch)
Acorn Plasma Takes care of any ''Tool'' settings. Acorn Plasma comes with all default Profiles from Hypertherm.
Acorn Plasma does not use any of the tool information from Sheetcam .
Sheetcam Has a forum if you really want the Sheetcam toolset.
Acorn Plasma does not use any of the tool information from Sheetcam .
Sheetcam Has a forum if you really want the Sheetcam toolset.