Search found 521 matches
- Tue May 07, 2024 5:37 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Machine parameter for Linear encoder input
- Replies: 6
- Views: 185
Re: Machine parameter for Linear encoder input
The AIKRON Model:AKM1 Has been Tested at Centroid. The Signal Type Needs to be the 5v RS422 https://www.aikrondro.com/product/aikron-akm-series-linear-encoders/ I've attached a snip of the DB9 connector of the Aikron and the Changes needed to match the Centroid DB9 Encoder Port. Aikron Scale Wiring....
- Tue May 07, 2024 4:47 pm
- Forum: Acorn CNC Plasma
- Topic: SheetCam Hypertherm 45XP .tool file (inch)
- Replies: 1
- Views: 72
Re: SheetCam Hypertherm 45XP .tool file (inch)
Acorn Plasma Takes care of any ''Tool'' settings. Acorn Plasma comes with all default Profiles from Hypertherm.
Acorn Plasma does not use any of the tool information from Sheetcam .
Sheetcam Has a forum if you really want the Sheetcam toolset.
Acorn Plasma does not use any of the tool information from Sheetcam .
Sheetcam Has a forum if you really want the Sheetcam toolset.
- Fri May 03, 2024 11:21 am
- Forum: Acorn CNC Plasma
- Topic: Please help! I fried my THC!!!
- Replies: 11
- Views: 1117
Re: Please help! I fried my THC!!!
Thats odd. Can you post a fresh report Please. The Report will have all you settings and macros. So I can then really see what the control is doing and why. Can you also Post the G-code used. I'm thinking the M61 macro is at fault of there is something going on in the G-code. Was the G-code job from...
- Wed May 01, 2024 5:50 pm
- Forum: Acorn CNC Plasma
- Topic: Please help! I fried my THC!!!
- Replies: 11
- Views: 1117
Re: Please help! I fried my THC!!!
Good choice on switching to the Everlast Torch Touch with Everlast and Primeweld is not officially supported by Centroid. I haven't seen another Everlast Using the TX torch touch yet. What does the Tin Wire connect too? I have seen the Primeweld Hooked up to the TX boards Torch touch and it seems to...
- Wed May 01, 2024 4:09 pm
- Forum: Acorn CNC Plasma
- Topic: Speed around corners
- Replies: 6
- Views: 428
Re: Speed around corners
Lowering the Parameter P223 should help with Arcs. I wouldn't take P223 below 100. Setting the Drives to 6400 and the wizard to match should also fix the speed up issue. The Laser offset issue is puzzling. I've even loaded your report on a fresh 5.08 build and Laser set X/Y functioned as expected. I...
- Fri Apr 26, 2024 12:39 pm
- Forum: Acorn CNC Plasma
- Topic: Torchmate accumove 2 conversion
- Replies: 52
- Views: 6111
Re: Torchmate accumove 2 conversion
Did you try the different duplex settings? I've seen some PC's that needed the Duplex setting changed or manually set.
100mps or 100 Half duplex or 100 full duplex.
100mps or 100 Half duplex or 100 full duplex.
- Thu Apr 25, 2024 8:43 pm
- Forum: Acorn CNC Plasma
- Topic: Speed around corners
- Replies: 6
- Views: 428
Re: Speed around corners
Those are some nice cuts. Clean and smooth. Is the Wizard set to 3200 steps/rev for X and Y? I think the last report I saw something like 6400 Can you post a fresh report with the latest settings. Can I see the dip switch settings on the drives? Did setting Parameter 223 to the 100-300 range help?
- Thu Apr 25, 2024 6:47 pm
- Forum: Acorn CNC Plasma
- Topic: Torchmate accumove 2 conversion
- Replies: 52
- Views: 6111
Re: Torchmate accumove 2 conversion
Seeing a lot of com errors in the msg log.
Have you tried disabling the windows firewall completely?
Have you tried disabling the windows firewall completely?
- Thu Apr 25, 2024 11:29 am
- Forum: Acorn CNC Plasma
- Topic: Torch stops and Rises up
- Replies: 1
- Views: 207
Re: Torch stops and Rises up
I run a CnC plasma but instade of firing the torch stops and Rises up. Could this be something that would be solved within the software.. Your Machine with Acorn Mill is Controlled by the Gcode completely. If the Job stops without an error in the message LOG. it was most Likely something in the Gco...
- Wed Apr 24, 2024 1:13 pm
- Forum: Acorn CNC Plasma
- Topic: Centroid v 4, extends and hits the material.
- Replies: 6
- Views: 464
Re: Centroid v 4, extends and hits the material.
Download TeamViewer
https://www.teamviewer.com
https://www.teamviewer.com