Search found 11 matches
- Sat Aug 28, 2021 8:12 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Acorn with CL-HSS57 Steppers, and KBMG212D, C89
- Replies: 23
- Views: 5252
Re: Acorn with CL-HSS57 Steppers, and KBMG212D, C89
SUCCESS!!! Third time is the charm. I had two bad KBMG-212D controller bought from ebay. The 3rd was new and works like a charm. This motor is very quite. Now I can move on with the rest of the restoration. Thank you Marty for being so patient and helping me trouble shoot the problem. It was just ba...
- Mon Aug 09, 2021 11:33 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Acorn with CL-HSS57 Steppers, and KBMG212D, C89
- Replies: 23
- Views: 5252
Re: Acorn with CL-HSS57 Steppers, and KBMG212D, C89
I will double check inside the Wizard that I have the right state chosen for output 4 & 5.martyscncgarage wrote: ↑Mon Aug 09, 2021 6:34 pm Then you had a closure of that enable circuit. Are you sure you are on NORMALLY OPEN contact on Acorn relay board?
The pictures show how I have the relays wired.
- Mon Aug 09, 2021 6:32 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Acorn with CL-HSS57 Steppers, and KBMG212D, C89
- Replies: 23
- Views: 5252
Re: Acorn with CL-HSS57 Steppers, and KBMG212D, C89
Yes. The jumper is not connected for Enable.
- Mon Aug 09, 2021 5:42 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Acorn with CL-HSS57 Steppers, and KBMG212D, C89
- Replies: 23
- Views: 5252
Re: Acorn with CL-HSS57 Steppers, and KBMG212D, C89
I decided to buy a second KBMG-212D driver to see if something was wrong with the driver. I swapped out all the connectors to the new driver after setting all the jumpers to match the original setup. After I checked my wiring a few times I decided to power up the system. When AC is applied to the Ac...
- Sat Jul 31, 2021 9:29 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Acorn with CL-HSS57 Steppers, and KBMG212D, C89
- Replies: 23
- Views: 5252
Re: Acorn with CL-HSS57 Steppers, and KBMG212D, C89
I installed the spindle drive and motor today for bench testing. KBMG212D with C89 board. I am not getting any rotation out of the motor so I must have something configured wrong. M3 S1000 command turns on relay 4 (Enable) but that is as far as it gets. I am not sure what to test yet. So I am reread...
- Thu Jul 29, 2021 11:37 am
- Forum: Centroid Acorn CNC Controller
- Topic: Acorn with CL-HSS57 Steppers, and KBMG212D, C89
- Replies: 23
- Views: 5252
Re: Acorn with CL-HSS57 Steppers, and KBMG212D, C89
Marty, I have the second stepper running now. I watched your Emco Compact 5 bench testing video where you explained how to set up CNC12 Lathe. Great video. The thing I am having the most trouble with (SOLVED) is setting the motor to revolve once per inch like yours did. The information on the motor ...
- Wed Jul 28, 2021 11:55 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Acorn with CL-HSS57 Steppers, and KBMG212D, C89
- Replies: 23
- Views: 5252
Re: Acorn with CL-HSS57 Steppers, and KBMG212D, C89
Todays mission was to get the CL-HSS57 closed loop steppers to spin. These drives are only similar to Leadshine, they are more like Steppersonline drives. These required the signal be inverted. I will post a picture of the Axis inputs and configurations I used. I will also post the schematic I made ...
- Tue Jul 27, 2021 5:45 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Acorn with CL-HSS57 Steppers, and KBMG212D, C89
- Replies: 23
- Views: 5252
Re: Acorn with CL-HSS57 Steppers, and KBMG212D, C89
I have a question regarding CNC12 update. I found the thread about updating to V4.62. My current version is CNC12 Mill Free 4.12 ( I bought the acorn a long time ago before I decided what machine I would put it on.). I want to install CNC12 Lathe instead of mill, then buy the full version of lathe. ...
- Sun Jul 25, 2021 10:24 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Acorn with CL-HSS57 Steppers, and KBMG212D, C89
- Replies: 23
- Views: 5252
- Sat Jul 24, 2021 12:22 am
- Forum: Centroid Acorn CNC Controller
- Topic: Acorn with CL-HSS57 Steppers, and KBMG212D, C89
- Replies: 23
- Views: 5252
Re: Acorn with CL-HSS57 Steppers, and KBMG212D, C89
Thank you for reviewing the drawing Marty. I appreciate all you do to help people.
I have wired up the Acorn and have a heartbeat. Now I need to follow the rest of the bench test advice. I'm looking forward to getting the Acorn working.
Bill
I have wired up the Acorn and have a heartbeat. Now I need to follow the rest of the bench test advice. I'm looking forward to getting the Acorn working.
Bill