Search found 16 matches
- Wed Oct 04, 2023 7:48 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Laser Software for Acorn
- Replies: 10
- Views: 1190
Re: Laser Software for Acorn
thank you all. I am still figuring out the best way to edit the NC file in Notepad++ as grossmsj mentioned I use "Emit S value for every G1 command" and make sure the "use G0 for overscan" is off otherwise the very next G1 after a G0 does not have an S command. in Notepad++ I rec...
- Wed Oct 04, 2023 11:41 am
- Forum: Centroid Acorn CNC Controller
- Topic: Laser Software for Acorn
- Replies: 10
- Views: 1190
Re: Laser Software for Acorn
suntravel, what machine type are you using in LightBurn?
my laser is setup with Acorn PWM on output 2, and using M37 for laser ON with S command for laser intensity.
my laser is setup with Acorn PWM on output 2, and using M37 for laser ON with S command for laser intensity.
- Wed Oct 04, 2023 11:37 am
- Forum: Centroid Acorn CNC Controller
- Topic: Laser Software for Acorn
- Replies: 10
- Views: 1190
Re: Laser Software for Acorn
Thank you Sword. I have used Ventric before, nice software.
Do you have any experience with the Laser Module add-on? can it be configured to output G-code ready for Acorn?
Do you have any experience with the Laser Module add-on? can it be configured to output G-code ready for Acorn?
- Wed Oct 04, 2023 11:17 am
- Forum: Centroid Acorn CNC Controller
- Topic: Laser Software for Acorn
- Replies: 10
- Views: 1190
Laser Software for Acorn
I have added a 20W Laser to my CNC router powered by the fantastic Acorn board.
I can run all sample G-code files provided by Centroid, but I have a hard time finding a laser engraving/cutting software.
can you please point me in the right direction. Thank you
I can run all sample G-code files provided by Centroid, but I have a hard time finding a laser engraving/cutting software.
can you please point me in the right direction. Thank you
- Wed Nov 16, 2022 7:11 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Acorn HomeALL
- Replies: 6
- Views: 744
Re: Acorn HomeALL
I feel bad asking this but I cannot find the location file for marco M91, M92 or M26.
do you mean to add feed speed in cncm.hom
M91/Y F5
M26/Y
would this work?
do you mean to add feed speed in cncm.hom
M91/Y F5
M26/Y
would this work?
- Fri Nov 11, 2022 6:34 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Acorn HomeALL
- Replies: 6
- Views: 744
Re: Acorn HomeALL
cnckeith, this is a Gerber Sabre retrofit, the limit switches are some king of magnetic 2 wire devices. there is a metal flat piece that fits inside the sensor and it stays tripped until you back up from the sensor. i have reduce the slow jog to 5 an Z and Y and i am now able to home all 3 axis. is ...
- Wed Nov 09, 2022 2:45 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Acorn HomeALL
- Replies: 6
- Views: 744
Acorn HomeALL
Hello, I need help with acorn homing. axis will still rotate after home switch it triggered this is a acorn installation using HomeAll, limit switched connected in series to Input1, and to -X -Y +Z all switched are tested and the Input1 is normally GREEN and turns RED when triggered I use the Wizard...
- Wed Jun 15, 2022 5:00 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Oak with Yaskawa Sigma I jerking
- Replies: 9
- Views: 1611
Re: Oak with Yaskawa Sigma I jerking
glad to report the 10:1 reducer is working VERY WELL.
thank you
thank you
- Wed Jun 15, 2022 4:58 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Pneumatic Pump Lubrication Sysyem
- Replies: 0
- Views: 1343
Pneumatic Pump Lubrication Sysyem
Hello, I am wondering if anyone has a similar lubrication system and if you found a way to control it by the OAK PLC. My is pneumatically actuated via a solenoid. I also have a low lube sensor (already connected to IN9), and another NC/NO sensor for cycle complete. My problem is that this pump can o...
- Mon May 09, 2022 7:33 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Oak with Yaskawa Sigma I jerking
- Replies: 9
- Views: 1611
Re: Oak with Yaskawa Sigma I jerking
so in my case i will need a 10:1 or better to do 1.6 revs for 1" travel
can you please help me locate a good supplier for the gear box.
thank you.
can you please help me locate a good supplier for the gear box.
thank you.