Search found 15 matches
- Tue Aug 30, 2022 6:48 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Drives that accept AC.
- Replies: 21
- Views: 4269
Re: Drives that accept AC.
My only source for Leadshine units is Leadshine usa I think is located in California, and I will never use another source.
- Tue Aug 30, 2022 6:41 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Rough edge quality on baltic birch plywood arcs
- Replies: 29
- Views: 3599
Re: Rough edge quality on baltic birch plywood arcs
Try to disable "smoothing edges". I had the same issue and I fixed this way.
- Fri Dec 31, 2021 10:51 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Drives that accept AC.
- Replies: 21
- Views: 4269
Re: Drives that accept AC.
I use Leadshine easy servo 220v 3ph closed loop steppers more than 8 years. I run very heavy woodworking steel router 5x12 feet . No gearboxes, no backlash. Amazing performance, very good speed, very high torque. Also very quiet and low working temperature. Very reliable drive. Also Acorn works supe...
- Tue Oct 27, 2020 9:47 am
- Forum: Centroid Acorn CNC Controller
- Topic: Refusing to measure ONLY tool #10? (Resolved)
- Replies: 17
- Views: 6673
Re: Refusing to measure ONLY tool #10? (Resolved)
Hi Swissi. Thanks for your advice. I updated to the last version. All looks fine. I don't want to open new post. Now the controller does not execute M30 command. This is first an second, when I tell in the wizard the thickness of my Tool touch plate , on the Parameters shows is negative, minus is in...
- Sat Oct 24, 2020 10:25 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Refusing to measure ONLY tool #10? (Resolved)
- Replies: 17
- Views: 6673
Re: Refusing to measure ONLY tool #10? (Resolved)
Sorry to get up this discussion . I did again tool number 10 as a Probe Tool, in the wizard, and the same issue is here again. This time the tool is not diamond, and the Z axis does not want to stop on the measuring procedure. It is obvious the software said to Acorn not to wait for a signal from th...
- Sat Oct 24, 2020 10:17 am
- Forum: Centroid Acorn CNC Controller
- Topic: Refusing to measure ONLY tool #10? (Resolved)
- Replies: 17
- Views: 6673
Re: Refusing to measure ONLY tool #10?
Hi Swissi. I changed the tool probe number to 100 and now tool number 10 is diamond tool and all is good. The diamond tools are conductive. I use diamond tools a lot and there is no problem with the conductivity of the diamond. Not only number 10 of my tools is diamond. Somehow the machine "kno...
- Fri Oct 23, 2020 4:47 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Refusing to measure ONLY tool #10? (Resolved)
- Replies: 17
- Views: 6673
Re: Refusing to measure ONLY tool #10?
Thanks. I will check.
- Fri Oct 23, 2020 4:41 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Refusing to measure ONLY tool #10? (Resolved)
- Replies: 17
- Views: 6673
Re: Refusing to measure ONLY tool #10?
Yes. I think so this is the problem. May be it is good to have some notification, or the automatic procedure not to start, to avoid some expensive crashes as mine. Thanks! What "Probe tool number" means to the machine?
- Fri Oct 23, 2020 4:33 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Refusing to measure ONLY tool #10? (Resolved)
- Replies: 17
- Views: 6673
Re: Refusing to measure ONLY tool #10?
Yes. The tool 10 is set on the wizard.
- Fri Oct 23, 2020 4:05 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Refusing to measure ONLY tool #10? (Resolved)
- Replies: 17
- Views: 6673
Refusing to measure ONLY tool #10? (Resolved)
Hi. Just started to remeasure my 16 tools on mine CNC router. Everything went smooth up to tool number 9. Started automatic measuring on tool number 10. Unfortunately the Z axis did not stop on the touch probe. The 700 dollars diamond tool was killed. Checked the tool touch probe- works fine on the ...