Centroid Community CNC Support Forum

karthick0320

martyscncgarage wrote: ↑Tue May 18, 2021 3:41 pm How old is your C86ACCP? What revision is on it?

My C86ACCP is more than a month old. I have the REV2.

karthick0320

Did you successfully bench test everything off the machine as you should have? THEN install them on the machine?

Unbelt the motors or take them off the machine. Get them turning off the machine first under CNC12 control.

I took the motors off the machine and I also removed the connection to ...

karthick0320

Go into the Wizard. INPUT screen
Go down to input 5. CLICK on the 5 to turn it from RED (NO) to Green (NC)
Write settings
Exit CNC12, restart CNC12
Retest

I tried it with green(normally closed) but it did not work so I was trying to see if NO would work.

What happens in either case is ...

karthick0320

Go into the Wizard. INPUT screen
Go down to input 5. CLICK on the 5 to turn it from RED (NO) to Green (NC)
Write settings
Exit CNC12, restart CNC12
Retest

I tried it with green(normally closed) but it did not work so I was trying to see if NO would work.

What happens in either case is that ...

karthick0320

martyscncgarage wrote: ↑Tue May 18, 2021 2:26 pm Post a screen shot of your diagnostic screen alt i

karthick0320

martyscncgarage wrote: ↑Tue May 18, 2021 1:34 pm
karthick0320 wrote: ↑Tue May 18, 2021 12:49 pm Hello Marty, thanks for the reply and I have attached the report with this reply. I had a look at the pictures and your video on the Clearpath SDSK bench testing, and also the Acorn CNC hookup schematics.
Does your C86ACCP match my configuration?

Here are some pictures for reference.

karthick0320

Hello Marty, thanks for the reply and I have attached the report with this reply. I had a look at the pictures and your video on the Clearpath SDSK bench testing, and also the Acorn CNC hookup schematics.

Does your C86ACCP match my configuration?

Yes it does. I followed the Acorn hookup ...

karthick0320

Hello Marty, thanks for the reply and I have attached the report with this reply. I had a look at the pictures and your video on the Clearpath SDSK bench testing, and also the Acorn CNC hookup schematics.

karthick0320

Hello, I am currently working with the Clearpath SDSK motors and the previous version of the C86ACCP interface for my Centroid Acorn CNC. Everything was going smooth, but after I added the drive fault relay and the no fault terminal, I keep getting the drive fault error messages repeatedly while ...

Centroid Community CNC Support Forum

Search found 9 matches

Re: New Build: SYIL X4 CNC Mill, Clearpath SDSK, C86ACCP & Centroid Acorn

Re: New Build: SYIL X4 CNC Mill, Clearpath SDSK, C86ACCP & Centroid Acorn

Re: New Build: SYIL X4 CNC Mill, Clearpath SDSK, C86ACCP & Centroid Acorn

Re: New Build: SYIL X4 CNC Mill, Clearpath SDSK, C86ACCP & Centroid Acorn

Re: New Build: SYIL X4 CNC Mill, Clearpath SDSK, C86ACCP & Centroid Acorn

Re: New Build: SYIL X4 CNC Mill, Clearpath SDSK, C86ACCP & Centroid Acorn

Re: New Build: SYIL X4 CNC Mill, Clearpath SDSK, C86ACCP & Centroid Acorn

Re: New Build: SYIL X4 CNC Mill, Clearpath SDSK, C86ACCP & Centroid Acorn

Re: New Build: SYIL X4 CNC Mill, Clearpath SDSK, C86ACCP & Centroid Acorn