Search found 68 matches
- Sun Oct 31, 2021 11:05 am
- Forum: Centroid Acorn CNC Controller
- Topic: Novakon Torus pro, Servo motor axis config. .850" off over 4"
- Replies: 16
- Views: 3497
Re: Novakon Torus pro, Servo motor axis config. Not even close
Your encoders are 2500 pulses per rev which is 10000 counts per rev. You don't tell us how the motors are connected to the ballscrews so I don't know if your turns per inch setting is correct. If your motors are direct coupled, then it is. You have resend requests in your error logs - this should b...
- Sun Oct 31, 2021 12:57 am
- Forum: Centroid Acorn CNC Controller
- Topic: Novakon Torus pro, Servo motor axis config. .850" off over 4"
- Replies: 16
- Views: 3497
Novakon Torus pro, Servo motor axis config. .850" off over 4"
Maybe I am missing something but I am trying to setup my axis config and I am having a hard time getting the movement dialed in. It seems to be way off yet, I should have 24" of x travel from the home limit and I am only getting about 18" on the readout. Hopefully someone can see my mistak...
- Sun Oct 31, 2021 12:49 am
- Forum: Centroid Acorn CNC Controller
- Topic: Prox switches only register as positive. Get stuck beyond switch?? **SOLVED** Use HOMEOK and proper soft limits
- Replies: 5
- Views: 1372
Prox switches only register as positive. Get stuck beyond switch?? **SOLVED** Use HOMEOK and proper soft limits
I have 3 proximity switches, one for each axis, with stops to trip them on each end. They wired to 3 different inputs. I have each input set to homeLimitOK for that axis. Per the Prox switch wiring diagram from Centroid website. My problem is acorn doesnt seem to realize which way I am moving when t...
- Sat Oct 30, 2021 2:06 am
- Forum: Centroid Acorn CNC Controller
- Topic: Centroid Acorn with servos? New build: Novakon Torus Pro
- Replies: 30
- Views: 9782
Re: Centroid Acorn with servos? New build: Novakon Torus Pro
Got the acorn communication with the 220v maxsine servo drivers all figured out. Pulse and Direction negative go to the acorn board. Pulse and Direction Positive go to 24v. ---------- you need to add a 1.5-2k ohm resistor between step/direction positive and 24v. All good now!!! 20211028_154446.jpg S...
- Sat Oct 30, 2021 2:00 am
- Forum: Centroid Acorn CNC Controller
- Topic: Help! No Virtual Jog Panel when starting cnc12 *SOLVED* set screen resolution to 1920×1080
- Replies: 13
- Views: 3435
Re: Help! No Virtual Jog Panel when starting cnc12 *SOLVED* set screen resolution to 1920×1080
I dont know what a report.zip is
- Wed Oct 27, 2021 3:46 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Help! No Virtual Jog Panel when starting cnc12 *SOLVED* set screen resolution to 1920×1080
- Replies: 13
- Views: 3435
Re: Help! No Virtual Jog Panel when starting cnc12 *SOLVED* set screen resolution to 1920×1080
SOLVED. by setting screen resolution to 1980×1020
It was set much lower. Thanks everyone.
It was set much lower. Thanks everyone.
- Wed Oct 27, 2021 3:36 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Help! No Virtual Jog Panel when starting cnc12 *SOLVED* set screen resolution to 1920×1080
- Replies: 13
- Views: 3435
- Wed Oct 27, 2021 3:33 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Help! No Virtual Jog Panel when starting cnc12 *SOLVED* set screen resolution to 1920×1080
- Replies: 13
- Views: 3435
- Wed Oct 27, 2021 3:30 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Help! No Virtual Jog Panel when starting cnc12 *SOLVED* set screen resolution to 1920×1080
- Replies: 13
- Views: 3435
- Wed Oct 27, 2021 3:06 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Help with connecting Maxsine 220v AC servo driver
- Replies: 12
- Views: 2748