Search found 29 matches
- Tue Feb 07, 2023 9:08 am
- Forum: Acorn CNC Plasma
- Topic: Buying a new plasma cutter
- Replies: 12
- Views: 2101
Re: Buying a new plasma cutter
Can I ask if it is necessary to get the Hypertherm WITH CPC control, I guess it seems obvious, but can't find it in the FAQ. Would be nice if you could use the Hypertherm Powermax 30.
- Thu Feb 02, 2023 10:03 am
- Forum: Acorn CNC Plasma
- Topic: Adding Plasma to my ShopBot CNC Router
- Replies: 1
- Views: 628
Adding Plasma to my ShopBot CNC Router
I have recently upgraded my 48x96 ShopBot to Acorn and now am seriously considering taking half my surface area and converting it to a plasma table. I am looking for some pointers on where to get started with the Acorn Part. I guess my main question is can I just add the extra boards and use my acor...
- Sun Dec 18, 2022 12:31 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Single Tool PostP for ShopBot and Other DIY Simple Machines
- Replies: 3
- Views: 831
Re: Single Tool PostP for ShopBot and Other DIY Simple Machines
Hello Gary, when I try to use this in my vCarve for ShopBot 7.5 It throws an error. Any ideas?
Seems to work fine in vCarve Desktop 9.5.
Seems to work fine in vCarve Desktop 9.5.
- Mon Dec 05, 2022 10:27 am
- Forum: Centroid Acorn CNC Controller
- Topic: Limit Switch Struggles Shopbot PRS
- Replies: 8
- Views: 805
Re: Limit Switch Struggles Shopbot PRS
Kurt... Maybe not the instructions on how to fix what you are experiencing, but advice in a different direction. This will allow you to make your machine perform better than it ever could on the SB3 control software. .... Thanks Gary, and for everyone's information, I wired them in series because t...
- Sun Dec 04, 2022 2:04 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Limit Switch Struggles Shopbot PRS
- Replies: 8
- Views: 805
Re: Limit Switch Struggles Shopbot PRS
Kurt, Are these mechanical switches or the SB 3 wire inductive? Assuming mechanical and with 3 tabs (com and NC or NO), are you sure that you have them wired in series properly? Check them for continuity when not tripped (closed). You can also use the I/O diagnostic screen to check the state of the...
- Sun Dec 04, 2022 12:48 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Limit Switch Struggles Shopbot PRS
- Replies: 8
- Views: 805
Limit Switch Struggles Shopbot PRS
I am attempting to get my limit switches working for simple safety tripping. I have X and Y limit switches. They are wired in series between common and Input 2 on the Acorn board. Acorn configuration shown in below image. If I set input 2 to NC I can move the machine, but limit switches do not trip....
- Sun Apr 24, 2022 7:51 am
- Forum: Centroid Acorn CNC Controller
- Topic: New Build - 2007 ShopBot PRS
- Replies: 17
- Views: 2455
Re: New Build - 2007 ShopBot PRS
Thanks Gary, I have been thinking about this for a while. I think I now understand the importance of this.Gary Campbell wrote: ↑Fri Apr 22, 2022 9:10 am Kurt...
.....
3) Items 1 and 2 are very important, read them again, out loud!
What type of touch probe would you recommend?
- Thu Apr 21, 2022 8:03 pm
- Forum: Centroid Acorn CNC Controller
- Topic: New Build - 2007 ShopBot PRS
- Replies: 17
- Views: 2455
Re: New Build - 2007 ShopBot PRS
The last piece of the Puzzle is my Z touch off plate. I watched a video by CNC Keith and he showed how to rig up a conductive probe. I gave it a shot this evening and I think I have it working. Below is video of my testing and touch off probe configuration.
- Thu Apr 21, 2022 12:25 pm
- Forum: Centroid Acorn CNC Controller
- Topic: New Build - 2007 ShopBot PRS
- Replies: 17
- Views: 2455
Re: New Build - 2007 ShopBot PRS
Tool Touch Off Probe: On my ShopBot I have a tool touch probe for setting Z zero height. Doesn't look like a switch, just a wire that I assume is grounded when it touches the touch off plate. It has 3 wires and black and green have continuity when the probe touches the plate as it is currently wired...
- Thu Apr 21, 2022 9:12 am
- Forum: Centroid Acorn CNC Controller
- Topic: New Build - 2007 ShopBot PRS
- Replies: 17
- Views: 2455
Re: New Build - 2007 ShopBot PRS
Now you have a different problem. If you correct the wiring and it works, great. If it doesn't it might be you now have bad prox switches from reversing the voltage to them. That was it Tom, I switched the wires and have a green light on Acorn Board and moving gantry the switch trips and clears per...