Search found 8 matches

by skibum-engineer
Thu Feb 18, 2021 4:46 pm
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Synchronize Spindle speed to live feed rate
Replies: 3
Views: 1840

Re: Synchronize Spindle speed to live feed rate

That sounds quite achievable, would this plc coding be in the area that Centroid could do? I guess I can ask for a PLC programming quote.
by skibum-engineer
Thu Feb 18, 2021 11:28 am
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Synchronize Spindle speed to live feed rate
Replies: 3
Views: 1840

Re: Synchronize Spindle speed to live feed rate

Quick Update I tried the below code with limited success: The result does scale via the feedrate override * by the commanded feedrate but it does not follow the actual feedrate which will change along the curves when accelerating or decelerating. That is the remaining challenge. Does anyone know how...
by skibum-engineer
Thu Feb 18, 2021 10:36 am
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Synchronize Spindle speed to live feed rate
Replies: 3
Views: 1840

Synchronize Spindle speed to live feed rate

Here is a Coding Idea I am trying to work on. Scaling the Spindle RPM command synchronous to the live feedrate of the running program. This is for use as an extrusion output in the place of a spindle. Existing Command: G01 X10 Y25 Z48 F200 S3000 The dream: Spindle RPM is a multiplier of actual feedr...
by skibum-engineer
Wed Feb 17, 2021 12:48 pm
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: OAK with DYN4 showing encoder errors <resolved>
Replies: 10
Views: 3370

Re: OAK with DYN4 showing encoder errors

I'm building a gigantic 3D Printer for construction
YEs counterweighted head, but I'll add a brake resistor if needed

I will actual have dual Xaxis and then a Zservo with break.
Setup picture will follow in a month or so.

Noted for the Reactor.
by skibum-engineer
Wed Feb 17, 2021 11:57 am
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: OAK with DYN4 showing encoder errors <resolved>
Replies: 10
Views: 3370

Re: OAK with DYN4 showing encoder errors

Cables were from DMM yes
It worked!
I have motion on all three drives.
The DMMDRV panel settings didn't stick on the Z drive (the screenshot i shared previously)
by skibum-engineer
Wed Feb 17, 2021 10:59 am
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: OAK with DYN4 showing encoder errors <resolved>
Replies: 10
Views: 3370

Re: OAK with DYN4 showing encoder errors

Thank you both very much for your replies and information Marty, I've attached the Report file. I set the Gear and Line to 2000 for all three drives I set the encoder count to 8000 for XYZ I Checked that Precision Mode was enabled (Param 256 set to 2) Tried to TUNE but Error: Status 6 cncsnw, I test...
by skibum-engineer
Thu Feb 11, 2021 9:47 pm
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: OAK with DYN4 showing encoder errors <resolved>
Replies: 10
Views: 3370

OAK with DYN4 showing encoder errors <resolved>

Hi all, My very first post here so please bear with me if its a bit incomplete or completely stupid. I've wired up 3 servos (DMM 1.3kW) with DYN4 drives and the Centroid Oak/DMM drive cables. After initial setup I'm trying to jog but get the following errors. 412 Xaxis (1) encoder differential error...
by skibum-engineer
Thu Feb 11, 2021 9:21 pm
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: OAK/DYN4
Replies: 116
Views: 39987

Re: OAK/DYN4

**** Disregard**** Made a new thread Hi all, My very first post here so please bear with me if its a bit incomplete or completely stupid. I've wired up 3 servos (DMM 1.3kW) with DYN4 drives and the Centroid Oak/DMM drive cables. After initial setup I'm trying to jog but get the following errors. 412...