Search found 18 matches
- Tue Feb 23, 2021 6:32 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: DB-9 Connector
- Replies: 7
- Views: 2859
Re: DB-9 Connector
Now the bad news. The plastic case is to wide to fit them on the All In One side by side. So chucked the case and wrapped them with rubber tape and ty-wraped the wire end. Still beats soldering them. replaced the screws with 4-40X3/8" long (Home Puke). Job done. Bob L Well done! Maybe you can ...
- Mon Feb 15, 2021 3:02 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: DB-9 Connector
- Replies: 7
- Views: 2859
Re: DB-9 Connector
Received mines today !
- Sat Feb 13, 2021 10:21 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Need Help ! Trak CNC2 conversion to Centroid Allin1DC
- Replies: 23
- Views: 7869
Re: Need Help ! Trak CNC2 conversion to Centroid Allin1DC
20210213_153424.jpg 20210213_135202.jpg 73,7 volts measured in condensater 1.Is this voltage level supported by allin1dc? 2.Should I keep the condensater, rectifier bridge and board of the old system? 3. After taking a look at the installation manual, I think that the only question where I may have...
- Fri Feb 12, 2021 4:48 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Need Help ! Trak CNC2 conversion to Centroid Allin1DC
- Replies: 23
- Views: 7869
Re: Need Help ! Trak CNC2 conversion to Centroid Allin1DC
Post pictures of what and where you are measuring.... You can do that by clicking on the Full Editor & Preview button below the box you type your message into, and then clicking on the Attachment's tab, also under the message box, and pointing to where you put the pictures on your computer. Mar...
- Fri Feb 12, 2021 2:12 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Need Help ! Trak CNC2 conversion to Centroid Allin1DC
- Replies: 23
- Views: 7869
Re: Need Help ! Trak CNC2 conversion to Centroid Allin1DC
The information i have:
Motor Voltage: 70 Volts
Motor Torque (X and Y axis) : 280 ozf.in (17,5 lbf.in or 2 Nm)
Motor Brand: i think is Magnetek (4040D-35 ...assembled in Mexico by Indiana Genera)l
Motor Voltage: 70 Volts
Motor Torque (X and Y axis) : 280 ozf.in (17,5 lbf.in or 2 Nm)
Motor Brand: i think is Magnetek (4040D-35 ...assembled in Mexico by Indiana Genera)l
- Fri Feb 12, 2021 2:06 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Need Help ! Trak CNC2 conversion to Centroid Allin1DC
- Replies: 23
- Views: 7869
Re: Need Help ! Trak CNC2 conversion to Centroid Allin1DC
Transformer output voltage to driver : 26 V Transformer output voltage to servomotor : 52 V Were those measurements AC Volts, or DC Volts? What is the DC voltage that you measure across the terminals of the large capacitor (which should be the DC Voltage going to the drives)? The output of a transf...
- Fri Feb 12, 2021 1:40 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Need Help ! Trak CNC2 conversion to Centroid Allin1DC
- Replies: 23
- Views: 7869
Re: Need Help ! Trak CNC2 conversion to Centroid Allin1DC
The capacitor is inside one black box where I think the servo drivers are around ... I will have to open the box ... Yes, I measured the current at the output of the transformer while JOG at maximum speed. I can always put a piece to work and measure the current in effort. In my case I think that th...
- Fri Feb 12, 2021 1:22 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: System Test, only one limit switch per axis
- Replies: 4
- Views: 1771
Re: System Test, only one limit switch per axis
well done ,
Can you take photo of the electrical box interior ?
Can you take photo of the electrical box interior ?
- Fri Feb 12, 2021 12:25 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Need Help ! Trak CNC2 conversion to Centroid Allin1DC
- Replies: 23
- Views: 7869
Re: Need Help ! Trak CNC2 conversion to Centroid Allin1DC
Hello! Today I asked a friend for help and we were taking measurements of the voltage and current values. Since I don't have these values written on my motors, I think it's important to measure them before taking apart the old control. To take the measurements i used JOG in maximum speed. The meas...
- Thu Feb 11, 2021 5:16 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: System Test, only one limit switch per axis
- Replies: 4
- Views: 1771
Re: System Test, only one limit switch per axis
Hello
I think you have to install a software limit but it is better to wait for an administrator to respond to answer you better.
I would like to see photos of the conversion of the protrak since this system is a cousin of mine.
Can you share some photos?
Thank you
I think you have to install a software limit but it is better to wait for an administrator to respond to answer you better.
I would like to see photos of the conversion of the protrak since this system is a cousin of mine.
Can you share some photos?
Thank you