Search found 18 matches

by Rui26
Tue Feb 23, 2021 6:32 am
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: DB-9 Connector
Replies: 7
Views: 2795

Re: DB-9 Connector

Now the bad news. The plastic case is to wide to fit them on the All In One side by side. So chucked the case and wrapped them with rubber tape and ty-wraped the wire end. Still beats soldering them. replaced the screws with 4-40X3/8" long (Home Puke). Job done. Bob L Well done! Maybe you can ...
by Rui26
Mon Feb 15, 2021 3:02 pm
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: DB-9 Connector
Replies: 7
Views: 2795

Re: DB-9 Connector

Received mines today !👍
20210215_175156.jpg
by Rui26
Sat Feb 13, 2021 10:21 am
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Need Help ! Trak CNC2 conversion to Centroid Allin1DC
Replies: 23
Views: 7676

Re: Need Help ! Trak CNC2 conversion to Centroid Allin1DC

20210213_153424.jpg 20210213_135202.jpg 73,7 volts measured in condensater 1.Is this voltage level supported by allin1dc? 2.Should I keep the condensater, rectifier bridge and board of the old system? 3. After taking a look at the installation manual, I think that the only question where I may have...
by Rui26
Fri Feb 12, 2021 4:48 pm
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Need Help ! Trak CNC2 conversion to Centroid Allin1DC
Replies: 23
Views: 7676

Re: Need Help ! Trak CNC2 conversion to Centroid Allin1DC

Post pictures of what and where you are measuring.... You can do that by clicking on the Full Editor & Preview button below the box you type your message into, and then clicking on the Attachment's tab, also under the message box, and pointing to where you put the pictures on your computer. Mar...
by Rui26
Fri Feb 12, 2021 2:12 pm
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Need Help ! Trak CNC2 conversion to Centroid Allin1DC
Replies: 23
Views: 7676

Re: Need Help ! Trak CNC2 conversion to Centroid Allin1DC

The information i have:

Motor Voltage: 70 Volts
Motor Torque (X and Y axis) : 280 ozf.in (17,5 lbf.in or 2 Nm)

Motor Brand: i think is Magnetek (4040D-35 ...assembled in Mexico by Indiana Genera)l
by Rui26
Fri Feb 12, 2021 2:06 pm
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Need Help ! Trak CNC2 conversion to Centroid Allin1DC
Replies: 23
Views: 7676

Re: Need Help ! Trak CNC2 conversion to Centroid Allin1DC

Transformer output voltage to driver : 26 V Transformer output voltage to servomotor : 52 V Were those measurements AC Volts, or DC Volts? What is the DC voltage that you measure across the terminals of the large capacitor (which should be the DC Voltage going to the drives)? The output of a transf...
by Rui26
Fri Feb 12, 2021 1:40 pm
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Need Help ! Trak CNC2 conversion to Centroid Allin1DC
Replies: 23
Views: 7676

Re: Need Help ! Trak CNC2 conversion to Centroid Allin1DC

The capacitor is inside one black box where I think the servo drivers are around ... I will have to open the box ... Yes, I measured the current at the output of the transformer while JOG at maximum speed. I can always put a piece to work and measure the current in effort. In my case I think that th...
by Rui26
Fri Feb 12, 2021 1:22 pm
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: System Test, only one limit switch per axis
Replies: 4
Views: 1747

Re: System Test, only one limit switch per axis

well done ,
Can you take photo of the electrical box interior ?
by Rui26
Fri Feb 12, 2021 12:25 pm
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Need Help ! Trak CNC2 conversion to Centroid Allin1DC
Replies: 23
Views: 7676

Re: Need Help ! Trak CNC2 conversion to Centroid Allin1DC

Hello! Today I asked a friend for help and we were taking measurements of the voltage and current values. Since I don't have these values ​​written on my motors, I think it's important to measure them before taking apart the old control. To take the measurements i used JOG in maximum speed. The meas...
by Rui26
Thu Feb 11, 2021 5:16 am
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: System Test, only one limit switch per axis
Replies: 4
Views: 1747

Re: System Test, only one limit switch per axis

Hello
I think you have to install a software limit but it is better to wait for an administrator to respond to answer you better.
I would like to see photos of the conversion of the protrak since this system is a cousin of mine.
Can you share some photos?
Thank you