Thanks,
Do you think my speeds you found will lead to troubles later? Other than just Jobs running slower?
Warm Regards, Mike
Search found 57 matches
- Fri Oct 06, 2023 11:04 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Moving X and A together(Thread)JUST CRAWLS
- Replies: 22
- Views: 7210
- Thu Oct 05, 2023 8:07 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Moving X and A together(Thread)JUST CRAWLS
- Replies: 22
- Views: 7210
Re: Moving X and A together(Thread)JUST CRAWLS
THANKS!!!! YOU GUYS ROCK ! PARAMETER 38 WAAS THE PROBLEM. My dealer set up much of the setup programming when I had finished the hardware, including 38. I didn't have a clue! (still don't unfortunately. I am 74. I forget most everything I knew when I don't use the Mill for months...) Your questions:...
- Thu Oct 05, 2023 9:48 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Moving X and A together(Thread)JUST CRAWLS
- Replies: 22
- Views: 7210
Re: Moving X and A together(Thread)JUST CRAWLS
My apologies, Mark, It was late at night and I was tired after 2 emergencies, rushing: As a former programmer, I know the importance of being precise.... SO: G1 G 91 F60 X1 runs 1 sec and all previous commands ran fast as expected, Then when you add A combined with X1 you get: G0 G91 A360 X1 crawls ...
- Wed Oct 04, 2023 8:36 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Moving X and A together(Thread)JUST CRAWLS
- Replies: 22
- Views: 7210
Re: Moving X and A together(Thread)JUST CRAWLS
Thanks cncsnw Mark. I did your requested tests listed in your previous post. Everything was as expected until you added x1, then it started crawling. I even tried 30 degrees over 1", still crawled, but the feedrate went up to 0.3. Setting Parameter 94 t0 2049 did not help, but appears to be req...
- Tue Oct 03, 2023 10:33 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Moving X and A together(Thread)JUST CRAWLS
- Replies: 22
- Views: 7210
Re: Moving X and A together(Thread)JUST CRAWLS
Could someone please tell me how to determine machine coordinates (what are machine coordinates?) of the z and y axis at the center line down the x axis which are required to be put in the parameters mentioned above.??? I can’t find any explanation of what this means. Please help! It’s still crawlin...
- Tue Oct 03, 2023 6:05 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Moving X and A together(Thread)JUST CRAWLS
- Replies: 22
- Views: 7210
Re: Moving X and A together(Thread)JUST CRAWLS
G93 F2 was tried as well as 5, no difference.
The 7900 was set up by the dealer. It runs fine otherwise, it doesn’t complain about the speed. This is a servo system.
O help,
Thanks, Mike
The 7900 was set up by the dealer. It runs fine otherwise, it doesn’t complain about the speed. This is a servo system.
O help,
Thanks, Mike
- Tue Oct 03, 2023 2:29 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Moving X and A together(Thread)JUST CRAWLS
- Replies: 22
- Views: 7210
Re: Moving X and A together(Thread)JUST CRAWLS
Uwe, how about 3 hours or more?, Mike
- Tue Oct 03, 2023 12:58 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Moving X and A together(Thread)JUST CRAWLS
- Replies: 22
- Views: 7210
Re: Moving X and A together(Thread)JUST CRAWLS
Help! I put 40 in the parameter 2, I prepositioned XO YO Z-0.05 A 360. THEN I put G93 G1 X 0.9235 Y0 Z -0.05 A -2160 F12. I included a screenshot. Note the feed rate 0 to 0,1 flashing IT STILL CRAWLS ! No faster THE REPORT.ZIP STILL APPLIES Please Help, I am stuck! I can't find a Tech bulletin. I ca...
- Mon Oct 02, 2023 9:15 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Moving X and A together(Thread)JUST CRAWLS
- Replies: 22
- Views: 7210
Moving X and A together(Thread)JUST CRAWLS
Gentlemen: I am attempting to cut a spiral using a linear move 1 inch in 8 turns. I am using a centroid factory A axis. The max speed setup is X =100, A=7900. When running each separately, they run normally at their set max speeds. when trying G1 X1 A 2880 F7800, It just crawls!! The onscreen feed r...
- Fri Sep 22, 2023 12:31 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Occasional manual override of lube
- Replies: 4
- Views: 4589
Re: Occasional manual override of lube
They turn on the mill for manual use. It sits unused most of the day. They use the mpg rather than the hand wheel. After a few weeks a pint of oil is on the floor so much that they unplugged the oiler. I guess I need to find a way to stop it because it leads them to unplug the oiler. After it has sa...