Search found 15 matches
- Thu Dec 17, 2020 3:09 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Acorn Tool Height offset problem
- Replies: 17
- Views: 8717
Re: Acorn Tool Height offset problem
Ok thanks been thru a lot here. That was it, I guess I was almost there. thank you for your response. I am working on why the post processor is putting a "0" at the end of the line, but until then Im just removing the "0" when it shows up. also had to add a "3000 M3" because the machine will not run ...
This post has been liked 0 time(s).
- Thu Dec 17, 2020 12:27 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Acorn Tool Height offset problem
- Replies: 17
- Views: 8717
Re: Acorn Tool Height offset problem
This is the tool change macro. How do in use g43 N#4120?
TOOLCHANGE_AdjustRegister = H
TOOLCHANGE_FirstMacroStart
[SEQ_PRECHAR][SEQNUM][DELIMITER]T[TOOL_NUM][DELIMITER]M06[DELIMITER]
[SEQ_PRECHAR][SEQNUM][DELIMITER][G_CODE][DELIMITER][NEXT_X][DELIMITER][NEXT_Y]
[SEQ_PRECHAR][SEQNUM][DELIMITER ...
TOOLCHANGE_AdjustRegister = H
TOOLCHANGE_FirstMacroStart
[SEQ_PRECHAR][SEQNUM][DELIMITER]T[TOOL_NUM][DELIMITER]M06[DELIMITER]
[SEQ_PRECHAR][SEQNUM][DELIMITER][G_CODE][DELIMITER][NEXT_X][DELIMITER][NEXT_Y]
[SEQ_PRECHAR][SEQNUM][DELIMITER ...
This post has been liked 0 time(s).
- Thu Dec 17, 2020 11:57 am
- Forum: Centroid Acorn CNC Controller
- Topic: Acorn Tool Height offset problem
- Replies: 17
- Views: 8717
- Thu Dec 17, 2020 2:28 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Velocity mode oak
- Replies: 10
- Views: 6134
Re: Velocity mode oak
thank you I found out what the deal is, the hurco already controls all of this and all I needed to to was complete the estop circuit. working great now. this oak control is awesome on my hurco the cuts are soooo much better. I am using the smoothing but couldn't be happier. I do have one more ...
This post has been liked 0 time(s).
- Thu Dec 17, 2020 2:15 am
- Forum: Centroid Acorn CNC Controller
- Topic: Acorn Tool Height offset problem
- Replies: 17
- Views: 8717
Re: Acorn Tool Height offset problem
Hi I could use some help here. I am not experienced with gcode never done it. let the post processor do it for me and frankly no time to learn it as im now 2 months behind because of installing an oak system. now that im cutting metal Im faced with the tool height offset system. never used anything ...
This post has been liked 0 time(s).
- Mon Dec 14, 2020 1:07 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Velocity mode oak
- Replies: 10
- Views: 6134
Re: Velocity mode oak
I am down to one last task, turning on the spindle. I have a manual speed control so don't require the analog 0-10v output. but that is all I seem to get and don't know how to use the spindle outputs, enable, reversing, and break. I know how to wire them but what parameters switches to manual ...
This post has been liked 0 time(s).
- Sun Dec 13, 2020 12:01 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Velocity mode oak
- Replies: 10
- Views: 6134
Re: Velocity mode oak
Ok all good. +-10 reversed on X axis. Very smooth. Love the fine control. Ran tuning and all looks great so far. Thank you for your help!!!!! Will
This post has been liked 0 time(s).
- Sat Dec 12, 2020 10:43 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Velocity mode oak
- Replies: 10
- Views: 6134
Re: Velocity mode oak
that worked im moving the x , y, z. that's a first. the x axis is very jumpy so looking at the info on that. go to run it and it jumps rapid and errors. others are very smooth.
This post has been liked 0 time(s).
- Sat Dec 12, 2020 8:58 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Velocity mode oak
- Replies: 10
- Views: 6134
Re: Velocity mode oak
yes the hurco servomate has a fault logic board so it does work for all three drives. just not sure of the internal wiring. rtb1-5 is ground to clear fault. thanks
This post has been liked 0 time(s).
- Sat Dec 12, 2020 8:52 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Velocity mode oak
- Replies: 10
- Views: 6134
Re: Velocity mode oak
Ok great thanks very much appreciated. Ive just spent last 3 hours looking for replacement drives and motors. even thinking stepper motors aaaccckkk.
I will try the jumper first, baby steps. there is a fault indicator and ground to clear fault rtb1-4 and 5 on the servomate but would there be just ...
I will try the jumper first, baby steps. there is a fault indicator and ground to clear fault rtb1-4 and 5 on the servomate but would there be just ...
This post has been liked 0 time(s).