Search found 397 matches

by ashesman
Mon Mar 18, 2024 2:26 am
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Actualizacion EMCO VCM 300
Replies: 158
Views: 25667

Re: Actualizacion EMCO VCM 300

I found a picture from when I made my cable and a photo of my cable. Don't laugh at my wiring, I made it in a hurry one night! The heatshrink contains resistors required to bias the RS-485 driver. Some cables need them and some have them built in. For example older FTDI drivers (very commonly used) ...
by ashesman
Sun Mar 17, 2024 8:39 pm
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Actualizacion EMCO VCM 300
Replies: 158
Views: 25667

Re: Actualizacion EMCO VCM 300

They often have duplicate signals to allow daisy chaining or fitting a terminating resistor. You should only need to connect up one of each signal. I will try to remember to find my cable tonight and send wiring.
by ashesman
Sun Mar 17, 2024 6:46 pm
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Actualizacion EMCO VCM 300
Replies: 158
Views: 25667

Re: Actualizacion EMCO VCM 300

Look in the C2000 manual, it has a picture. You only need to co next + and -. Its not a bad idea to also connect gnd but 5v is not required.
by ashesman
Sun Mar 17, 2024 5:57 pm
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Actualizacion EMCO VCM 300
Replies: 158
Views: 25667

Re: Actualizacion EMCO VCM 300

Download for free from the delta website.

Note that some of those rs-485 cables require resistors to be wired between 5v/gnd and the a/b signals. Check the manual for the adapter you get.
by ashesman
Sun Mar 17, 2024 4:52 pm
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Actualizacion EMCO VCM 300
Replies: 158
Views: 25667

Re: Actualizacion EMCO VCM 300

It's just three sets of motor ratings. You could use any of them. You could use the lower frequency data for the rated values and set max frequency to the highest. But using the upper set if you intend to run it at the upper range is probably most accurate. Your problem is over current error during ...
by ashesman
Sun Mar 17, 2024 3:23 pm
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Actualizacion EMCO VCM 300
Replies: 158
Views: 25667

Re: Actualizacion EMCO VCM 300

I haven't had time to read the instructions. To convert between decimal, binary and hexadecimal numbers, use windows calculator in programmers mode. There are tons of pages and videos explaining these numbers. To start/stop your drive for tuning, if you have it set up for remote control, then drive ...
by ashesman
Tue Mar 05, 2024 4:41 am
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Actualizacion EMCO VCM 300
Replies: 158
Views: 25667

Re: Actualizacion EMCO VCM 300

Have you let the drive go through its self tune procedure to characterize the motor? This motor appears to be an induction motor, are you running the drive in induction motor mode? Honestly, I am going to keep saying it... You need to start diagnosing the problem. There is probably no-one that can m...
by ashesman
Mon Mar 04, 2024 11:59 pm
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Actualizacion EMCO VCM 300
Replies: 158
Views: 25667

Re: Actualizacion EMCO VCM 300

I just went through the delta web site for support.

How sure are you that your motor is set up correctly induction/permanent magnet motor and all the parameters are correct. Encoder and resolver all wired correctly and in phase?
by ashesman
Mon Mar 04, 2024 8:48 pm
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Actualizacion EMCO VCM 300
Replies: 158
Views: 25667

Re: Actualizacion EMCO VCM 300

Just search usb rs-485 and you will find heaps of options. Then just cut up an old ethernet cable and wire it to it. Braking resistors dont get very hot. They take a lot of repeated stops to get really hot What is the exact error code so I can look it up in the manual. Not sure about using automatic...
by ashesman
Mon Mar 04, 2024 7:01 pm
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Actualizacion EMCO VCM 300
Replies: 158
Views: 25667

Re: Actualizacion EMCO VCM 300

The motor driver takes the AC mains and converts it to DC on its internal bus. Then it converts that DC to the driving AC for the motor at whatever frequency is required. During deceleration, the motor acts like a generator making AC. The drive converts that AC to DC current on to its internal bus. ...