Search found 401 matches
- Sat Apr 13, 2024 4:29 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: How to go outside soft travel limits?
- Replies: 5
- Views: 1094
Re: How to go outside soft travel limits?
I did exactly this in my M6 macro. I'm not near the machine right now to get it. If you search my name you should be able to find a report.zip file with it in there though. The only catch was that if you cancel/stop during a tool change, then you get left with the y limit wrong. But running a succes...
- Mon Apr 08, 2024 3:53 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: CNC12 5.08 Upgrade Issues
- Replies: 12
- Views: 996
Re: CNC12 5.08 Upgrade Issues
Any updates on this?
- Sat Apr 06, 2024 2:27 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Intercon drilling cycle warning
- Replies: 2
- Views: 103
Re: Intercon drilling cycle warning
Hanks. Thats kind of what I thought, and that's what the g code said, but didnt make sense to me in the picture.
- Fri Apr 05, 2024 8:51 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Intercon drilling cycle warning
- Replies: 2
- Views: 103
Intercon drilling cycle warning
Also, how come there are no intercon menus for pexk drilling cycles like g73? I rarely use intercon and today had a play.
- Mon Mar 18, 2024 2:26 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Actualizacion EMCO VCM 300
- Replies: 158
- Views: 27311
Re: Actualizacion EMCO VCM 300
I found a picture from when I made my cable and a photo of my cable. Don't laugh at my wiring, I made it in a hurry one night! The heatshrink contains resistors required to bias the RS-485 driver. Some cables need them and some have them built in. For example older FTDI drivers (very commonly used) ...
- Sun Mar 17, 2024 8:39 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Actualizacion EMCO VCM 300
- Replies: 158
- Views: 27311
Re: Actualizacion EMCO VCM 300
They often have duplicate signals to allow daisy chaining or fitting a terminating resistor. You should only need to connect up one of each signal. I will try to remember to find my cable tonight and send wiring.
- Sun Mar 17, 2024 6:46 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Actualizacion EMCO VCM 300
- Replies: 158
- Views: 27311
Re: Actualizacion EMCO VCM 300
Look in the C2000 manual, it has a picture. You only need to co next + and -. Its not a bad idea to also connect gnd but 5v is not required.
- Sun Mar 17, 2024 5:57 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Actualizacion EMCO VCM 300
- Replies: 158
- Views: 27311
Re: Actualizacion EMCO VCM 300
Download for free from the delta website.
Note that some of those rs-485 cables require resistors to be wired between 5v/gnd and the a/b signals. Check the manual for the adapter you get.
Note that some of those rs-485 cables require resistors to be wired between 5v/gnd and the a/b signals. Check the manual for the adapter you get.
- Sun Mar 17, 2024 4:52 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Actualizacion EMCO VCM 300
- Replies: 158
- Views: 27311
Re: Actualizacion EMCO VCM 300
It's just three sets of motor ratings. You could use any of them. You could use the lower frequency data for the rated values and set max frequency to the highest. But using the upper set if you intend to run it at the upper range is probably most accurate. Your problem is over current error during ...
- Sun Mar 17, 2024 3:23 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Actualizacion EMCO VCM 300
- Replies: 158
- Views: 27311
Re: Actualizacion EMCO VCM 300
I haven't had time to read the instructions. To convert between decimal, binary and hexadecimal numbers, use windows calculator in programmers mode. There are tons of pages and videos explaining these numbers. To start/stop your drive for tuning, if you have it set up for remote control, then drive ...