Search found 8 matches
- Fri Mar 22, 2024 11:08 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Please help with ATC issue after spindle and VFD upgrade
- Replies: 4
- Views: 151
Please help with ATC issue after spindle and VFD upgrade
Hi All, We could use some help getting our ATC working after a spindle and VFD upgrade. We are running Acorn 4.64. We build guitars. We were running a CNC Depot 530C WITH a HITACHI J-200. We just installed a CNC Depot RM50C spindle and a Automation Direct GS-23 VFD. The RM 50C does not have any outp...
- Thu Jul 06, 2023 6:54 pm
- Forum: Centroid Acorn CNC Controller
- Topic: My mdi will not execute commands
- Replies: 6
- Views: 429
Re: My mdi will not execute commands
working with earlier report
- Thu Jul 06, 2023 4:59 pm
- Forum: Centroid Acorn CNC Controller
- Topic: My mdi will not execute commands
- Replies: 6
- Views: 429
Re: My mdi will not execute commands
i am now
- Wed Jul 05, 2023 10:43 am
- Forum: Centroid Acorn CNC Controller
- Topic: My mdi will not execute commands
- Replies: 6
- Views: 429
My mdi will not execute commands
How to recent power surge while I had my WCS open. I thought all I lost was all my WCS Settings. I did do a restore to my last report But when I input a command like T1 M6 Nothing happens . I have acorn 5 I understand it's a parameter or somewhere in the 8 hundreds but not sure which and how to fix ...
- Mon Oct 10, 2022 5:17 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Wandering home zero’s on Centroid Acorn driven router
- Replies: 3
- Views: 485
Re: Wandering home zero’s on Centroid Acorn driven router
Hi Shawn, We have discovered that our issue is a mechanical belt / backlash issue. I think we are good. Thank you so much, attached is a link to our Dropbox with all the detail that you require to help us should we need it in the future. https://www.dropbox.com/sh/5hueqarg9fvanxa/AADYvi6dzJG9ugyuTr3...
- Mon Oct 10, 2022 1:05 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Wandering home zero’s on Centroid Acorn driven router
- Replies: 3
- Views: 485
Wandering home zero’s on Centroid Acorn driven router
Hello All, We are in the initial stages of setting up our new CNC gantry router with using a Centroid Acorn controller. We have sent the machine home and then repeatedly back to a 1/4” reamed location hole in both the machine table plate and the 1/4” reamed hole on our fixture plate. After doing so ...
- Sun Nov 15, 2020 8:16 pm
- Forum: Centroid Acorn CNC Controller
- Topic: I am a newbie to this forum. need help wiring up DP-4 touch probe
- Replies: 4
- Views: 1204
Re: I am a newbie to this forum. need help wiring up DP-4 touch probe
Yes I have the schematic and can read it . I have the 11805 that came with probe. I thought that 8 din plug would just plug in to the board beacuse, I am using all centroid part, At the very least, provide the male side of the plug to make your own leads. The directions did not say any thing about m...
- Sun Nov 15, 2020 4:37 pm
- Forum: Centroid Acorn CNC Controller
- Topic: I am a newbie to this forum. need help wiring up DP-4 touch probe
- Replies: 4
- Views: 1204
I am a newbie to this forum. need help wiring up DP-4 touch probe
Is there a step by step vid. of directions to hook up the DP-4 . I have acorn 12 pro v4.5 with the RV.4 board on a 3 axis router. The wiring connector they include is not near long enough to route all the way through the gantry and underside cable management to the control box. I see on the version ...