Search found 16 matches

by Aly-Tek
Fri Jan 13, 2023 12:21 am
Forum: Acorn CNC Plasma
Topic: Torch Touch off issue
Replies: 10
Views: 1716

Re: Torch Touch off issue

Thanks again for you help Joey. You beat me to replying again before you got on ;) I think it's sorted :D . What I found, I had a faulty Float switch. When I jiggled the cable near the switch it faulted so I just replaced it (could have been connection but who cares its replaced) and I've just cut 4...
by Aly-Tek
Thu Jan 12, 2023 7:55 pm
Forum: Acorn CNC Plasma
Topic: Torch Touch off issue
Replies: 10
Views: 1716

Re: Torch Touch off issue

Thanks Joey, That's got me on the right path, thank you ;) I still have the Z ploughing into the table. What I found so far was my Z pitch was out (fixed) then reset all measurements associated with Z and re-run the torch calibration. Everything when perfect 8-) I then tried to cut the 4" line ...
by Aly-Tek
Wed Jan 11, 2023 9:30 pm
Forum: Acorn CNC Plasma
Topic: Torch Touch off issue
Replies: 10
Views: 1716

Re: Torch Touch off issue

Ok one thing to add, I've realized I hadn't done the torch calibration yet so while doing this I've realized it doesn't change everything from imperial to metric. I.E when doing the calibration it asks for a 2" test cut but registers as 50.8mm while cutting (perfect) but then says .6" safe...
by Aly-Tek
Wed Jan 11, 2023 6:05 pm
Forum: Acorn CNC Plasma
Topic: Torch Touch off issue
Replies: 10
Views: 1716

Re: Torch Touch off issue

Hi Joey, Thanks, surprisingly it's hard work to make sure it looks nice and clean :mrgreen: The breakaway and float switch are seperate. This is the Z unit I used https://step-motion.com/collections/plasma-floating-lifters/products/z-axis-lifter-plasma-cnc-200mm-travel-magnetic-breakaway-floating-sy...
by Aly-Tek
Wed Jan 11, 2023 3:45 am
Forum: Acorn CNC Plasma
Topic: Torch Touch off issue
Replies: 10
Views: 1716

Torch Touch off issue

Hi Brains trust I have finally got my box all sorted and table moving about (just waiting for a new Z axis Limit switch) My issue is the torch touch off. I have a Float switch connected to input 4 and a Prox switch for Breakaway connected to input 5 if I manually move the Z down to actuate the float...
by Aly-Tek
Tue Nov 29, 2022 7:03 pm
Forum: Acorn CNC Plasma
Topic: Stepper only turns in positive direction
Replies: 9
Views: 1808

Re: Stepper only turns in positive direction

cnckeith wrote: Mon Nov 28, 2022 5:49 pm i moved this post to the plasma forum.
Thanks Keith, as it was more a generic question to just the Acorn and stepper I didn't think to place it here.

I am curious though, could the plasma side of the boards be interfering this here?
by Aly-Tek
Tue Nov 29, 2022 7:01 pm
Forum: Acorn CNC Plasma
Topic: Stepper only turns in positive direction
Replies: 9
Views: 1808

Re: Stepper only turns in positive direction

You may not have done anything wrong. Just check your stepper drive switches and see if one of them changes the motion from single direction to bi-directional. I see a lot of them defaulted to move in a single direction! Dave C. Switches haven't changed since the bench test. I did buy a new stepper...
by Aly-Tek
Tue Nov 29, 2022 6:54 pm
Forum: Acorn CNC Plasma
Topic: Stepper only turns in positive direction
Replies: 9
Views: 1808

Re: Stepper only turns in positive direction

Not sure if this helps but the last config change you made was to set the travel limits of X Axis to both -200 and +200 (metric of course). All other axes have + and - set to zero meaning no soft limits. At the very next restart the log shows "WARNING: The unlock for the Scales feature is not ...
by Aly-Tek
Sat Nov 26, 2022 6:52 am
Forum: Acorn CNC Plasma
Topic: Stepper only turns in positive direction
Replies: 9
Views: 1808

Stepper only turns in positive direction

Hi Brains trust, I am installing the Plasma Acorn controller and have done something I am unaware of :( I'm hoping someone can point me in the right direction. I performed the Acorn bench test as soon as it arrive, everything went smoothly. I then proceeded to bench test a Stepper motor, perfect (ge...
by Aly-Tek
Wed Apr 21, 2021 11:04 pm
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: New Oak Install
Replies: 27
Views: 8115

Re: New Oak Install

Hey CrossFireX, do you have the Fuji Frenic 5000 MS5 VFD? I may have the cable you need for your MPG also as I replaced all my cables for the servos and drivers but it won't have the fancy coil to it :P I could only wish mine was under 10K so far I'm pushing 20K including cables and fittings. One th...