Search found 95 matches

by mrp192
Wed Aug 03, 2022 9:53 pm
Forum: Centroid Acorn CNC Controller
Topic: New Build, PM2700 lathe with Acorn, Videos and Photos <upgraded to AC servos>
Replies: 93
Views: 87120

Re: New Build, PM2700 lathe with Acorn, Videos and Photos <upgraded to AC servos>

Hey, Where did you get these from? or what are these style din rail blocks called?

Thanks,
Brent
suntravel wrote: Fri Mar 04, 2022 4:34 pm


Image

by mrp192
Fri Jun 17, 2022 3:55 pm
Forum: Centroid Acorn CNC Controller
Topic: ProbeApp V3: The Ultimate Probe Software for CNC12
Replies: 68
Views: 117490

Re: ProbeApp V3: The Ultimate Probe Software for CNC12

I'm back from the something...... Anyways here my Swissi powered extending ATC rack.

by mrp192
Fri Dec 10, 2021 12:29 pm
Forum: Centroid Acorn CNC Controller
Topic: Laser/Router Work Flow
Replies: 29
Views: 19296

Re: Laser/Router Work Flow

While G54, G55, etc. may work, I think it would be easier to have your post for the laser use a G52 XY offset for the laser. Have the post apply the offset at the start of the file and then reset it at the end. So, lets say that you set the XY location for your spindle tool at your intended locatio...
by mrp192
Fri Dec 10, 2021 11:26 am
Forum: Centroid Acorn CNC Controller
Topic: Laser/Router Work Flow
Replies: 29
Views: 19296

Re: Laser/Router Work Flow

cnckeith wrote: Fri Dec 10, 2021 12:23 amsure.
I have never had to set that up so what would be a good way of going it?
by mrp192
Fri Dec 10, 2021 12:07 am
Forum: Centroid Acorn CNC Controller
Topic: Laser/Router Work Flow
Replies: 29
Views: 19296

Re: Laser/Router Work Flow

yes, there are several ways to do this most all of them use the Work Coordinate System part zero positions. G54 for Mill, G55 for Laser. Is there way that I can setup G55 so I don't need to set it up again? So the laser is mounted on the side of the spindle. So if I probe in G54 and then I can swit...
by mrp192
Mon Dec 06, 2021 10:04 pm
Forum: Centroid Acorn CNC Controller
Topic: Emco PC Turn 50 ATC issue
Replies: 48
Views: 12201

Re: Emco PC Turn 50 ATC issue

Here is a fresh report.
by mrp192
Mon Dec 06, 2021 1:23 pm
Forum: Centroid Acorn CNC Controller
Topic: Emco PC Turn 50 ATC issue
Replies: 48
Views: 12201

Re: Emco PC Turn 50 ATC issue

You need to tell us which ATC program and schematic you are using You need to recap what sensors are on the turret. We do need a fresh report. WHAT is Parameter 849? As I mentioned, I am very concerned about the speed at which the turret is rotating. You can slow the turret down by dropping the vol...
by mrp192
Mon Dec 06, 2021 12:55 pm
Forum: Centroid Acorn CNC Controller
Topic: Emco PC Turn 50 ATC issue
Replies: 48
Views: 12201

Re: Emco PC Turn 50 ATC issue

Alright so from the beginning. These are the settings that I entered. from the Acorn counter based tool turret with home sensor Instructions A. Parameter #6 = 1 B. Parameter #160 = 1 (Sets ATC to non-random type meaning it puts tools back into same positions) C. Parameter #161 = Maximum number of to...
by mrp192
Sun Dec 05, 2021 10:16 pm
Forum: Centroid Acorn CNC Controller
Topic: Emco PC Turn 50 ATC issue
Replies: 48
Views: 12201

Re: Emco PC Turn 50 ATC issue

Ok I am back at this again. I did upgrade the motor so now I have use 24v forward and 12v to hold it against the paw. But I am still having issues. Hopefully this video explains what is going on.
by mrp192
Wed Dec 01, 2021 9:21 pm
Forum: Centroid Acorn CNC Controller
Topic: Router + Laser
Replies: 1
Views: 884

Router + Laser

Hi everyone,
I am attaching a laser to my router. When I go a M37 the spindle will start spinning and I will get nothing from the laser. As far as I can tell I set everything up correctly. Any advise would be great.