Search found 15 matches
- Mon Dec 20, 2021 12:59 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Z-Axis Limits, Will not pass system test
- Replies: 4
- Views: 1195
Re: Z-Axis Limits, Will not pass system test
So I adjusted the z- limit, ran the system test and it passed! The only issue I am left with is the z+ home position not being in the correct location for the tool changer claw. I thought I made the change correctly but it is not taking. How do I go about changing this? And if I do, do I need to rer...
- Sun Dec 19, 2021 8:46 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Z-Axis Limits, Will not pass system test
- Replies: 4
- Views: 1195
Z-Axis Limits, Will not pass system test
Long story short i recently had an issue with my z-axis and had to take it apart and put it back together. Everything seemed fine after reassembly until I noticed the position of the spindle was not in the correct location for the tool changer claw. To correct this I adjusted the soft limits and aft...
- Mon Sep 13, 2021 9:12 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: OAK Spindle load meter <<Answered>>
- Replies: 9
- Views: 4894
Re: OAK Spindle load meter <<Answered>>
Thank you! Everything is working again. Has anyone been able to get x-y-z axis load meters to work with DMM DYN4 servo motors?
- Sat Sep 11, 2021 7:25 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: OAK Spindle load meter <<Answered>>
- Replies: 9
- Views: 4894
Re: OAK Spindle load meter <<Answered>>
Hi everyone after reading this post it inspired me to get my load meter working. I did follow the TSB for setting the machine parameters and in the PLC I changed the spindle axis from 5 to 6 and successfully compiled. Unfortunately now when I start my machine and reset the e-stop I can manually star...
- Sun Jun 13, 2021 10:58 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Oak H1 Power Connector
- Replies: 3
- Views: 1892
Re: Oak H1 Power Connector
Tblough,
Thank you for the advice, I will reconnect the mean-well power supply.
Robbie
Thank you for the advice, I will reconnect the mean-well power supply.
Robbie
- Wed Jun 09, 2021 5:05 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Oak H1 Power Connector
- Replies: 3
- Views: 1892
Oak H1 Power Connector
I am in the process of putting all of my CNC components in an enclosure. In the enclosure I have 3 separate ABB power supplies 5V, 12V, and 24V. What I would like to do is connect the oak board to these power supplies and no longer use the mean-well. However upon disconnecting it I quickly grew conf...
- Sat Nov 07, 2020 10:03 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Inverter reset oak output 5 (Resolved)
- Replies: 6
- Views: 2814
Re: Inverter reset oak output 5
Thank you
- Thu Nov 05, 2020 7:45 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Inverter reset oak output 5 (Resolved)
- Replies: 6
- Views: 2814
Re: Inverter reset oak output 5
Attached is my report
- Thu Nov 05, 2020 6:40 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Inverter reset oak output 5 (Resolved)
- Replies: 6
- Views: 2814
Inverter reset oak output 5 (Resolved)
Over the past few days I have finally been able to get my VFD wired up and configured. Everything seems to be functioning as it should except for the inverter reset. I can only get continuity between the OAK output 5 and common if I force the output but cannot get it to work using the virtual contro...
- Tue Nov 03, 2020 11:34 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Incremental Jog (Resolved)
- Replies: 8
- Views: 2951
Re: Incremental Jog (Resolved)
Will do Marty. thank you for all of the videos you have posted. They were very helpful in helping me get my system up and running. i am in the process of cleaning up wiring and buttoning up some things but once I get something semi-presentable I will definitely post a video.